background image

10

A

B

A

B

SPEAKER LEVEL INPUT

R

L

LEFT

RIGHT

SPEAKER LEVEL INPUT

LEFT

BRIDGED

RIGHT

A

B

SPEAKER OUTPUT

POWER IN

FUSE(25A)

BATT

P.CON(REMOTE)

GND

25

LE

FT

RIG

HT

SPEAKER LEVEL INPUT

• The genuine-accessory car stereo shall have a maximum power output of no more than 25 W.
• Do not connect the speaker output leads from a power amplifier (Optional) to the speaker input

terminals of this unit, for this may cause malfunction  or damage. 

• Connect the power control lead to a power supply which can be turned ON/OFF by the ignition

key switch (ACC line). 
With this connection, shock noise may be generated when the power of the genuine-accessory
car stereo is switched ON/OFF.

2

CAUTION

Genuine-accessory

car stereo

Speaker level input connection

Connect the unit by inserting it in the connection between the genuine-accessory car stereo
and speakers.

Do not connect cables and leads to both RCA cable input  jacks and the speaker input terminals
simultaneously,  for this may cause malfunction or damage.

2

CAUTION

Lead terminal
(Commercially available parts)

Connection 

To Power control
(REMOTE) terminal

Front Left 

Front Right 

Rear Right 

Rear Left 

A

Left input

B

Left input

A

Right input

B

Right input

Car fuse
box

ACC

Battery

Содержание KAC-648













Отзывы: