Kenwood CMOS-210 Скачать руководство пользователя страница 10

10

   

|

   

CMOS-310/CMOS-210

Overhead View Image Adjustment 
(Up-and-Down Angle)

This item adjusts the vertical angle (inclination) of the 
camera installation position.

1

  Select “OVERHEAD VIEW IMAGE ADJUSTMENT 

(Up-and-Down ANGLE)”.

2

  Press the + or – button of the switch unit so 

that the lines indicating the vehicle width are 
shown vertical.

Adjustment is possible by one step up and down. If the 
adjustment is not possible in the currently available range, 
change the camera position before retrying.

3

  After completing the adjustment, press the 

view button.

4

 Select 

[Next].

  Advances to “WIDE VIEW GUIDELINE 

ADJUSTMENT (Size)”.

For Guideline Adjustment

•  The subsequent adjustments adjust the sizes, lengths and positions 

of the guidelines displayed in the wide view and overhead view. 
By default, three guidelines shown below (green, yellow and red) 
are displayed assuming that the camera installation height is 80 
cm (2.62 feet) and that the distance between the left and right 
lines of the parking space is 2.2 meters (7.22 feet). Adjusting the 
wide view or overhead guidelines alters the interval between the 
corresponding guidelines. As the interval between each set of 
guidelines varies depending on the camera installation height, 
check the actual settings after all of the following adjustments are 
completed.

•  Once the interval between guidelines has been adjusted according 

to your parking space, the displayed guidelines do no longer 
indicate the width of the vehicle. Note that the sizes of parking 
space are greatly variable and confirm the actual size of each 
parking space before attempting to park in it.

•  The orange line indicates the position of the overhead view (area 

on the near side of the orange line) and of the wide view (area 
beyond the orange line) in the PinP view (page 14). When the 
orange line displayed in the wide view exceeds the parking line, 
slow down the vehicle and move until the red line (parking 
position) by checking it in the overhead view.

•  The red line is used to indicate the parking position and can set it 

independently from other guide lines.

Green

Yellow

Red

0.5 m
(1.64 feet)

Orange

2.7 m
(8.86 feet)

2.2 m (7.22 feet)

Camera Setting (CMOS-310 only)

  

 

Содержание CMOS-210
















Отзывы: