background image

OPERATING INSTRUCTIONS

DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE.
DO NOT USE OR STORE FLAMMABLE MATERIALS NEAR THIS APPLIANCE.
DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN
OPERATION.

LIGHTING AND RUNNING THE FIRE:-

• Open the gas supply valve behind the appliance, if fitted.

CAUTION: If the main burner has been alight, wait two to three minutes to allow it to cool before re-

lighting it.

• Press down on the control knob at the top of the heater and turn it slowly anticlockwise. The piezo

igniter will click as a spark jumps across the terminals at the pilot light. It may be necessary to repeat
this a number of times before the pilot ignites if there is air in the pilot light pipeline.

• Keep holding the control knob down for 15 to 30 seconds after ignition. Release the pressure on the

control knob – the pilot should remain alight when the knob rises.

• Turn the control fully anticlockwise to the ‘HIGH’ position and the fire will light at full heat. There may

be a strong smell the first time the logs are fired but this will soon disappear.

• After ten minutes, set the control to give the desired heat output.

TURNING THE FIRE OFF:-

• Push down and turn the control to the ‘PILOT’ position. The pilot will remain alight.
• To extinguish the pilot light on STD models, press down on the control and turn it fully clockwise to

the ‘OFF’ position.

CLEANING INSTRUCTIONS

The outside of the cabinet and glass should need no more than an occasional wipe with a damp cloth to
remove any dust which may have settled.

All visible flame gas heaters can produce small amounts of soot, particularly if the combustion air entry
slots under the heater are obstructed or the aeration air inlets are clogged with lint.

After a time, the inside of the glass may require cleaning. To do this, carefully remove the three glass

pieces (See Glass Removal and Assembly, page 8), and clean their inside surfaces with a non-abrasive cloth
and a non-scratching, NON-CAUSTIC type household cleaning liquid. Replace the parts as detailed on
page 8, keeping fingerprints off the inside glass surfaces.

No other user maintenance should be necessary. If you require any other service or adjustments, contact
your Installer or Dealer.

2

Содержание Estate LP Gas Fire













Отзывы: