background image

CLEANING DIRECTIONS

 

 

1) Turn all Switches OFF.

 

2) Disconnect the machine Solution 
Hose. Pull down on the middle of the 
brass Coupler. The hose will release. 
While holding down the Coupler, 
insert the Hand Tool Kit Solution 
Hose. Release Coupler. Pull on

 

the Solution hose to insure it is 
secured.

 

3) Disconnect the grey and black 
Vacuum Cuffs at the back of the 
machine. Connect the grey 
Hand Tool Kit Cuff to the grey 
machine Cuff.

 

 

 

WARNING: 

Do Not Use To Clean Haitian Cotton!

 

 

1) Read 

7 IN 1 Carpet Care 

directions. 

See: Test Colorfastness and 
Upholstery Cleaning  Directions.

 

Mix 

7 IN 1 

with water in Bucket 

according to directions.

 

Note: 

For upholstery 

cleaning, mix 1.5 
gallons of cleaner

 

at a time.

 

1) 

Important: 

Pour contents of Bucket 

into machine Solution Tank.

 

1) See Preparing Carpet & Upholstery.

 

2) Turn ON the Suction and Hand Tool Switches.

 

3) Squeeze the Hand Tool Trigger as you pull 
up or back with overlapping even strokes.

 

 
 
 
 
 
 
 
 

 

Cleaning Stairs

 

1. Use the Hand Tool to clean stairs. (See Cleaning Upholstery to hook up hand  tool.)

 

2. Clean the upstairs rooms first, then the stairs.

 

IMPORTANT: 

When cleaning the upper stairs, turn machine sideways so wheels are NOT facing forward, toward stairs. 

Be careful bringing the machine down wet stairs. Make sure to empty the Bucket and Solution Tank using the Drain  Hose.

 

3.  Turn on Suction and Hand Tool  Switches.

 

4.  Place Hand Tool Suction Nozzle on carpet and squeeze Trigger while pulling  backwards.

 

Cleaning  Machine

 

1) Wipe hair and debris from the Lid.

 

2) Drain unused solution from Solution  Tank.

 

3) Dispose of solution and rinse Bucket  thoroughly.

 

4) Clean out the Vac Nozzle with a hanger.

 

5) Remove fibers and hair from the Brush.

 

6) Wipe Brush Chamber clean with towel.

 

7) Wipe off the exterior of the machine with a damp  towel.

 

 

Spray/Brush 

Trigger  Switch

 

Suction Switch 

Handle Adjust

 

Lid 

Bucket 
Handle

 

Bucket

 

 
 
 
 
 

 

Sight 

Tubes

 

Handle

 

Hoses

 

Solution

 

Tank 

 

Drain Hose

 

 

Suction  Nozzle

 

/ Brush

 

 
 
 

 

4

 

C

le

a

n

in

g

 U

p

h

o

ls

te

ry

 

Содержание C4-100A













































Отзывы: