Kent Euroclean SelectGloss 21PH, Руководство оператора и список запасных частей

Страница: 6 / 32

FORM NO. 56041536 - SelectGloss ™ 21PH, 21PK, 27PK, 27PO, 27PR - 5 55 55
MACHINE SET UP MACHINE SET UP MACHINE SET UP MACHINE SET UP MACHINE SET UP
CHECKING OIL LEVEL AND FIL CHECKING OIL LEVEL AND FIL
CHECKING OIL LEVEL AND FIL CHECKING OIL LEVEL AND FIL CHECKING OIL LEVEL AND FILTERS
TERS
TERS TERS TERS
1 Check oil level prior to starting machine. Use proper amount and
specified oil, in order to prevent engine damage. When filling or
changing oil, add more than one quart (946.3ml) -then check dip
stick In cap. Add additional oil If necessary but do not overfull
The manufacturer recommends the use of 10W30 oil. ALWAYS CHECK
OIL DAILY BEFORE USING MACHINE.
A A
A A
ATTENTION! TTENTION!
TTENTION! TTENTION!
TTENTION!
When checking oil, machine should be turned OFF and on level surface.
Remove dipstick and wipe clean, then replace dipstick. For Honda,
Kawasaki and Robin the cap should not be screwed In. To check Onan
engine, the cap must be screwed In all the way. ALWAYS REFER TO YOUR
ENGINE MANUAL.
2 Be sure air filter Is free of dust/debris and other obstructions.
3 Check and clean recoil and carburetor filters If necessary. (See
Engine Owners Manual)
ADJUSTING HANDLE HEIGHT ADJUSTING HANDLE HEIGHT
ADJUSTING HANDLE HEIGHT ADJUSTING HANDLE HEIGHT ADJUSTING HANDLE HEIGHT
Machine is equipped with an adjustable handle for comfort and use of
operators of different heights. With a 9/16" wrench, simply adjust handle
at pivot points until desired operating position Is reached and then
retighten bolts.
INST INST
INST INST
INSTALLING OR CHANGING LPG FUEL ALLING OR CHANGING LPG FUEL
ALLING OR CHANGING LPG FUEL ALLING OR CHANGING LPG FUEL
ALLING OR CHANGING LPG FUEL
T T T T TANK ANK ANK ANK ANK
NOTE: For refueling tank, see “REFUELING AND STORING TANKS”.
1 Push machine In a designated safe area.
NOTE: Move to Step 6 for tank installation.
2 Close LPG tank valve on installed tank.
3 Operate engine until it stops from lack of fuel. (See Machine
Owners Operation)
FOR SAFETY: Never release or bleed tank Inside building or en- FOR SAFETY: Never release or bleed tank Inside building or en- FOR SAFETY: Never release or bleed tank Inside building or en- FOR SAFETY: Never release or bleed tank Inside building or en- FOR SAFETY: Never release or bleed tank Inside building or en-
closed areas.
closed areas. closed areas. closed areas. closed areas.
FOR SAFETY: When servicing machine, keep flames and sparks
FOR SAFETY: When servicing machine, keep flames and sparks
FOR SAFETY: When servicing machine, keep flames and sparks FOR SAFETY: When servicing machine, keep flames and sparks FOR SAFETY: When servicing machine, keep flames and sparks
away from fuel system service area. Keep area well ventilated.
away from fuel system service area. Keep area well ventilated.
away from fuel system service area. Keep area well ventilated. away from fuel system service area. Keep area well ventilated.
away from fuel system service area. Keep area well ventilated.
4 Put on gloves and remove service coupling by turning counter-
clockwise.
-
5 Unlatch and remove empty LPG fuel tank from machine and
store tank in a designated, safe area.
6 Carefully put full LPG tank on machine and position valve nozzle
towards engine.
NOTE: Make sure LPG fuel tank matches fuel system (Vapor System
Only).
CAUTION! CAUTION! CAUTION! CAUTION! CAUTION!
Never use a fuel tank not Intended for machine.
7 Fasten tank hold-down clamp to securely lock tank in position.
Adjustment to hold-down clamp can be made by threading latch
in or out.
8 Connect LPG fuel hose to valve nozzle by turning service cou-
pling clockwise (Tighten according to tank supplier recommen-
dations). Make sure service coupling Is clean and free of
damage. Also, make sure It matches machine service coupling.
A A
A A
ATTENTION! TTENTION!
TTENTION! TTENTION!
TTENTION!
When Installing tank, be careful not to cross thread service
coupling.
9 Open tank service valve slowly and check for leaks. Close
service valve immediately if a LPG leak Is detected.
INST INST
INST INST INSTALLING OR REMOVING P
ALLING OR REMOVING P
ALLING OR REMOVING P ALLING OR REMOVING P ALLING OR REMOVING PAD DRIVER
AD DRIVER
AD DRIVER AD DRIVER AD DRIVER
AND P AND P
AND P AND P
AND PADS ADS
ADS ADS
ADS
Consult an authorized distributor to assist you in choosing the correct
pad for your specific cleaning need.
Pad Driver Installation:
Pad Driver Installation: Pad Driver Installation: Pad Driver Installation: Pad Driver Installation:
1 Lean machine on left side (Dip stick tube down).
2 Place pad driver on drive shaft and spin pad driver clockwise to
install.
Pad Installation: Pad Installation: Pad Installation: Pad Installation: Pad Installation:
1 Tilt machine back on the rear caster (Park Position).
2 Remove plastic centerlock ring from pad driver. Center pad on
pad driver and secure with centerlock ring.
Pad Driver Removal : Pad Driver Removal : Pad Driver Removal : Pad Driver Removal : Pad Driver Removal :
1 With knee, apply downward pressure on bell of machine deck.
2 Place 3/4" (19 mm). Open end wrench onto top of drive shaft.
3 With rubber mallet, strike wrench to break loose shaft from pad
driver (counter-clockwise).
4 Lean machine on left side (Dip stick tube down).
5 Remove pad driver by spinning off counter-clockwise.
revised 03-7