background image

Safety and Care Advice

Important -

 Please read these instructions fully before starting assembly

• 

Warning:

 This unit weighs 

approximately 54kgs.

Please lift with care.

• Check you have all the

components and tools listed on 

pages 2 and 3.

• Remove all fittings from the 

plastic bags and separate them 

into their groups.

• Keep children and animals 

away from the work area, small 

parts could choke if swallowed.

• Parts of the assembly will be 

easier with 2 people.

• Make sure you have enough 

space to layout the parts before 

starting.

• Do not stand or put weight on 

the product, this could cause 

damage.

• Assemble the item as close to 

its final position (in the same 

room) as possible.

• Assemble on a soft level 

surface to avoid damaging the 

unit or your floor (use opened  

out unit carton).

1

Care and maintenance

• Only clean using a damp cloth 

and mild detergent, do no use 

bleach or abrasive cleaners. 

• From time to time check that 

there are no loose screws on 

this unit.

• This product should not be 

discarded with household 

waste. Take to your local

authority waste disposal centre.

• We do not

recommend the 

use of power 

drill/drivers 

for 

inserting screws

,

as this could damage the unit.

Only use hand screwdrivers.

• 

Safety note:

 It is

recommended that this unit is 

secured to a wall using the 

overbalance protector kit 

supplied or, an alternative fixing 

method of your choice.

• Dispose of all packaging 

carefully and responsibly.

Drawer Front

 

(DF2414)

(79.1 x 19.2cm)

Drawer Back 

(W765-124)

(76.5 x 12.4cm)

Left Drawer Side 

(W370-124LH)

(37 x 12.4cm)

Drawer Base 

(T776-367)

(77.6 x 36.7cm)

Right Drawer Side 

(W370-124RH)

(37 x 12.4cm)

Components - 

Panels

Please check you have all the panels listed below

If you need help or have damaged or missing parts, please visit www.argos-support.co.uk 
or email: [email protected] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928. 
For any other queries please contact the Customer Helpline on: 0345 640 2020

1

2

3

4

5

Tools required

Scissors / Rule / Hammer / Cross-head screwdriver / Square / Spirit level / Step ladder

Eye protection (when using a hammer or drill) / Electric drill (only use when drilling into walls)

Содержание 404/4275





















Отзывы: