Kensence S-MIX-PRO1600 Скачать руководство пользователя страница 3

Страница: 3 / 25

S-MIX-PRO1600

To protect the device and operating personnel from electrostatic discharge, you need to check and

ensure that the device is grounding good before the device is powered on. Please

observe the following

when you install, use, maintain this equipment.

Make sure the device ground connection.

Please use single-phase three wire system AC 220V power supply, and ensure all transmission

system is grounding good.

To protect operating personnel and the device ,please turn off all power supplies and pull the plug

before moving the device or doing some specific works witch need to be done when the electricity is

turned off . Please turn off the main power switch on rainy days or when not in use for a long time.

Please do not put anything upon the cables, or tread the cables .

To avoid damaging the device , please turn off power supply before plugging cable into the device or

pulling cable from device. The damage caused by plugging/ pulling cables without turning off power

supply is outside the scope of the warranty.

The power of the device gives out heat when it works, so it’s necessary to keep the work environment

ventilated to protect the device from the damage caused by over temperature.

Do not place the device in very cold or very hot places. Do not sprinkle any corrosive chemicals or

liquid on or around the device.

To avoid accident or any further damage ,non-professionals please do not dismantle or maintain the

device without permission.

Do not sprinkle any corrosive chemicals or liquid on or around the device.

Safety Reminder

Содержание S-MIX-PRO1600


























Результаты поиска

Содержание S-MIX-PRO1600

Отзывы:

Похожие инструкции для S-MIX-PRO1600

Бренды по названию

Популярные бренды

Kensence S-MIX-PRO1600, Руководство по эксплуатации

Результаты поиска

Содержание S-MIX-PRO1600

Отзывы:

Похожие инструкции для S-MIX-PRO1600

Бренды по названию

Популярные бренды