manualshive.com logo in svg

Kenmore W10035270, Техническое руководство

Поделиться
Скачать
Kenmore W10035270 Скачать руководство пользователя страница 12

03/06

FOR SERVICE TECHNICIAN’S USE ONLY

PART NO. W10035270

TECH SHEET - DO NOT DISCARD

PAGE 12

5.

The user interface assembly is held to
the console insert panel by three
screws and two locking tabs. After the
screws are removed, lift each of the
locking tabs to remove the back cover
of the user interface assembly. See
figure 15, page 11.

6.

Remove the cycle selector switch from
the user interface assembly opening
by lifting the locking tab on the cycle
selector switch and turning the
selector switch in a counterclockwise
direction. See figure 17.

7.

Locking tabs located at the bottom of
the console insert panel secure the
user interface assembly to the console
insert panel. Using a flat-blade
screwdriver, gently apply pressure to
the locking tabs to release the user
interface assembly. See figure 17.

SOFTWARE COPYRIGHTED.

MANUFACTURED UNDER ONE OR MORE

OF THE FOLLOWING U.S. PATENTS:

4,669,200
4,700,495
4,754,556
4,840,285
4,865,366
4,899,464
4,908,959

4,989,347
5,066,050
5,560,120
5,809,828
6,020,698
6,047,486
6,199,300

6,446,357
6,597,144
6,604,298
6,685,241
6,732,447
6,784,673
6,819,255

D314,261
D314,262
D457,991
D457,992
D495,453

P9

1

5

1

P8

P14

P2

3

1

1

6

P4

1

1

8

3

P5

P3

1

P13

1

P/N XXXXXX   Re

v X

Date Code

YDDD-xx

XXXX-XXX

MADE IN COO

N.O.

Black

COM

Red

Heater

Relay 1

Motor

Relay

Tan

Black-White

White

Green-Yellow

Brown

Blue

Black

Heater Relay 2

(Dual Element Model Only)

Yellow-Red

COM

Violet

N.O.

Black

Figure 16.

Machine control electronics.

Reinstalling the Electronic
Assemblies

Refer to preceding removal sections and
replace in reverse order.

NOTE:

When replacing the cycle selector

switch, make sure that the shaft is positioned
through the center of the shaft seal that is
captive between the decorative overlay and
the console panel insert.

NOTE:

When reconnecting wire

connections, be sure to route the user
interface wires beneath the retainer clips on
the user interface back cover.

Figure 17.

Gently apply pressure to

locking tabs to release the user interface
assembly.

REMOVING THE BACK PANEL

1.

Unplug dryer or disconnect power.

2.

Remove the cover plate screw and cover
plate. See figure 18.

3.

Remove the nine rear screws from the
back panel, then remove panel.

Cover Plate

Figure 18.

Remove screws.

Содержание W10035270













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды