Kenmore SPACEMASTER 85210 Скачать руководство пользователя страница 5

Страница: 5 / 16

- 5 -

THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN:

NOTE:

You may not use all of these parts.

NOTE:

You need to install at least one lag screw into a 2" x 4" stud and four anchor bolts into the wall and the
mounting area must meet the 150+ lbs. weight requirement.

PARTS, TOOLS, MATERIALS

Damper/duct connector

(for roof-venting or wall -venting installation)

Two tapping screws

(for attaching the damper duct connector)

Four 1/4" x 2" lag screws

(for wall stud holes)

Four 1/4" x 3" toggle bolts

(for drywall holes)

Two 1/4" x 2" bolts

(for securing to the upper cabinet)

Two washers

(for the two upper cabinet bolts)

Four spring toggle heads

(for the toggle bolts)

One power cord bushing

(for the cord hole in a metal upper cabinet)

One lock pin and one washer

One power cord clamp and
One dark-colored mounting screw

(to hold the power cord)

Содержание SPACEMASTER 85210

















Результаты поиска

Содержание SPACEMASTER 85210

Отзывы:

Бренды по названию

Популярные бренды

Kenmore SPACEMASTER 85210, Руководство по установке

Результаты поиска

Содержание SPACEMASTER 85210

Отзывы:

Бренды по названию

Популярные бренды