Kenmore KM1000 Скачать руководство пользователя страница 56

Страница: 56 / 68

Installing Your Water Optimizer

Installing Your Water Optimizer

2-54

Diagram 2.8.4 -

Open Shutoff Valve

You should hear water running and filling the Optimizer’s tanks. Check for leaks, and wait

until the sound of water running stops.

Once the Optimizer is filled, plug it in, but do not flip on the power switches yet.

We need to flush each temperature mode. Start by flushing the

Ambient Mode

into

your large container for 30 seconds. Press the light blue

Ambient Mode Button

to begin

dispensing.

Now, for the best experience, we recommend flushing the full tank capacity for both the

Hot Mode

and

Cold Mode

. For reference, the

Hot Tank

capacity is

0.26 gal (1 liter)

and the

Cold Tank

capacity is

1.1 gal (4.16 liters)

. For directions on how to flush your

appliance, see the included

Use & Care Guide

, or the

Quick Start Sticker

applied to

your Water Optimizer’s control panel.

9. If you haven’t connected any accessory appliances to your new Water Optimizer, you

are finished!!! You can now proceed to power on your Optimizer (

see Use & Care

Guide for instructions

10. If you have connected accessory appliances, you can now open the

1/4 in. Quick Connect Shutoff Valve(s)

connected to your

Accessory Line

. Water

should now start flowing into your accessory appliances. Check the lines, valve, and

Содержание KM1000





































































Результаты поиска

Содержание KM1000

Отзывы:

Kenmore KM1000, Руководство по установке, Страница: 56 / 68

Результаты поиска

Содержание KM1000

Отзывы: