Kenmore KM1000 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 68

Kenmore KM1000 Скачать руководство пользователя страница 21

Installing Your Water Optimizer

Installing Your Water Optimizer

2-19

connection is almost certainly a ½ in. (Nominal/NPT) fitting. If you have a 15/16 in. and
a 1 in. wrench, you can check to confirm by attempting to loosen the connection (there
is 1/16 in. range of variance between different plumbing fittings).

IF THAT DOESN’T FIT,

you have an extremely rare setup, and should contact a plumber.

IF THE LARGER

WRENCH DOES FIT, we don’t provide 1/2 in. adapter in your kit (only 2.5% of our
customers require it), but we’d be more than happy to ship you one for free upon request.
Call us at

1-844-374-6576

, or email us at

[email protected]

.

Or, if you don’t

want to wait, you can pick one up at your local hardware store. Ask for a

1/2 in (FIP) x

1/2 in. (MIP) x 1/4 in (OD) Push-to-Connect Angle Stop Adapter Valve

.

Diagram 2.3(B).5

Detach Cold Water Feed Line

6. Next, screw the bottom (female) end of

3/8 in. Sink Adapter Valve

to the

top (male) end of

Cold Water Shutoff Valve

using your hand. Then tighten

using medium force with the same wrench (11/16 in.) you used to remove

Cold Water Feed Line

.

«
...
19
20
21
22
23
...
»

Содержание KM1000





































































Отзывы:

Нет отзывов