manualshive.com logo in svg

Kenmore Elite 625.386200, Инструкция по использованию и уходу, Страница: 4 / 32

Поделиться
Скачать
Kenmore Elite 625.386200 Скачать руководство пользователя страница 4

4

Questions? Call the Kenmore Water Line 1-800-426-9345.

FCC Notice

Safety Guides

p

Read all steps and guides carefully before installing

and using your new water softener.  Follow all steps

exactly to correctly install.  Failure to follow them

could cause personal injury or property damage.

Reading this manual will also help you to get all the

benefits from your water softener.

p

Your Kenmore

®

Elite Hybrid Water Softener will

reduce hardness minerals from water.  This is meas-

ured in grains per gallon (gpg).  It will also remove

some clear water iron*.  This is measured in parts

per million (ppm).  See the specifications page for

the maximum limit of hardness removal.  It will also

reduce taste and odor in water, and will reduce bar-

ium and radium 226/228 in water (see performance

data sheet for details).

p

A water softener will not improve other water problems

such as acidity or iron other than clear water iron.

p

Do not attempt to use this product to make safe

drinking water from non-potable water sources.  Do

not use the system on microbiologically unsafe water,

or water of unknown quality without adequate disin-

fection before or after the system.

p

Check with your local public works department for

plumbing and sanitation codes.  You must follow

their guides as you install the system.  Follow your

local codes if they differ with guides in this manual.

In Massachusetts, plumbing code 248-CMR 3.00 and

10.00 shall be adhered to.  Consult with a licensed

plumber.

* The capacity to reduce clear water iron is substantiat-

ed by Water Quality Association test data.

p

Use only lead-free solder and flux for all sweat-solder

connections, as required by federal codes, when

installing soldered copper plumbing.

p

Use care when handling the water softener.  Do not

turn upside down or drop.

p

Avoid installing in direct sunlight.  Excessive heat may

cause distortion or other damage to non-metallic parts.

p

This water softener works on water pressures of 20 psi

(minimum) to 125 psi (maximum).  If your house water

pressure is over the maximum, install a pressure reduc-

ing valve in the water supply pipe to the softener.

p

Temperature of the water supply to the softener must be

between 40°F and 100°F.  Do not install on hot water.

p

If installing the water softener outdoors, do not locate

where it will be exposed to wet weather, direct sunlight

or extreme hot or cold temperatures.

p

This water softener works on 28V DC electrical power,

supplied by a direct plug-in power supply (included).

Be sure to use the included power supply and plug it into

a nominal 120V, 60 Hz household outlet that is in a

dry location only, grounded and properly protected by

an overcurrent device such as a circuit breaker or fuse.

p

This water softener has a non-metallic valve system.

Installing it on metal plumbing will break electrical

continuity, which may interrupt grounding for the

home.  You must restore electrical continuity in your

metal plumbing system (See Page 11).

FCC NOTICE

NOTE:

This equipment has been tested and found to

comply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules.  These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.  This

equipment generates, uses, and can radiate radio fre-

quency energy and, if not installed and used in accor-

dance with the instructions may cause harmful interfer-

ence to radio communications.

However, there is no guarantee that interference will not

occur in a particular installation.  If this equipment does

cause harmful interference to radio or television recep-

tion, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

p

Reorient or relocate the receiving antenna.

p

Increase the separation between the equipment and

receiver.

p

Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

p

Consult the dealer or an experienced radio/TV

technician for help.

IMPORTANT:

Changes or modifications not expressly

approved by the party responsible for compliance

could void the user’s authority to operate the equip-

ment.

INDUSTRY CANADA NOTICE

This device complies with Industry Canada Standard

RSS-210.  Operation is subject to the following two con-

ditions: (1) this device may not cause interference, and

(2) this device must accept any interference, including

interference that may cause undesired operation of the

device.

Содержание Elite 625.386200

































Отзывы:

Нет отзывов