manualshive.com logo in svg

Kenmore Elite 625.386200, Инструкция по использованию и уходу, Страница: 27 / 32

Поделиться
Скачать
Kenmore Elite 625.386200 Скачать руководство пользователя страница 27

27

Questions? Call the Kenmore Water Line 1-800-426-9345.

Service Information

NO

Valve

Motor

Position

Switch

NC

Back of Electronic

Controller (PWA)

Pwr.

In

Position/

Turbine Motor

28V DC

120V AC 

60 Hz

Power

Supply

C

org

grn

Turbine

Sensor

+5

OUT

GND

WIRING SCHEMATIC

Figure 48

Salt Lid

Sensor

Tank

Light

Figure 47

RETURNING TO CONNECT MODE

Once a connection has been made to the Kenmore

®

cloud, as described on page 16, the softener’s electronic

controller will maintain it.  If, for example, connection is

temporarily lost due to an internet service interruption,

the system will automatically reconnect when service is

restored.
An exception is if you replace your local Wi-Fi router.

The softener will not automatically connect to the new

router, but must be manually placed into Connect Mode

and connected again.
To return the softener to Connect Mode:

1.

Press the CONNECT SMART button and hold for 5

seconds.

2.

The blue connection status light should begin flash-

ing, indicating that the unit is in Connect Mode

awaiting connection.

3.

Connect the system to the Kenmore

®

cloud, as

described on page 17.

3.

Press the SELECT button, and the electronic controller

will restart.

4.

Set the present time, hardness, etc., as described on

pages 14 & 15.

RESETTING TO FACTORY DEFAULTS

To reset the electronic controller to its factory default

for all settings (time, hardness, etc.):

1.

Press the SELECT button and hold it until the display

changes twice to show the flashing model code.

2.

Press the 

r

UP button to display a flashing “SoS”.

European Directive 2002/96/EC requires all electrical and electronic

equipment to be disposed of according to Waste Electrical and Electronic

Equipment (WEEE) requirements.  This directive or similar laws are in

place nationally and can vary from region to region.  Please refer to your

state and local laws for proper disposal of this equipment.

Содержание Elite 625.386200

































Отзывы:

Нет отзывов