Kenmore 796.4102#90# Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 62

background image

There’s built-in AC 120V and DC power in output terminal of PWB assembly in common. Be careful
electric shock when disconnecting parts while trouble shooting. (Wear Electro Static Discharge gloves
when working.)
After cutting off the power when changing PWB assembly, disconnect or assemble.
Be careful static when handling PWB assembly, and use Electro Static Discharge plastic pack when
delivering or keeping it.

22

8. TROUBLESHOOTING

8-1. SAFETY CAUTION

8-2. ERROR MODE SUMMERY

ERROR

SYMPTOM

CAUSE

WATER INLET

ERROR

1

UNBALANCE

ERROR

2

DRAIN

ERROR

3

OVER FLOW

ERROR

4

PRESSURE

SENEOR

ERROR

5

DOOR OPEN

ERROR

6

HEATING

ERROR

7

• Correct water level (246) is not reached within 8 minutes

after water is supplied or it does not reach the preset water
level within 25 minutes.

• The load is too small.
• The appliance is tilted.
• Laundry is gathered to one side.
• Non distributable things are put into the drum.

• Door not all the way closed.
• Loose electrical connections at Door switch and PWB

Assembly.

• The DOOR SWITCH ASSEMBLY is out of order.

• Not fully drained within 10 minutes.

• The SENSOR SWITCH ASSEMBLY is out of order.

• The THERMISTOR is out order.

• Water is overflowing (water level frequency is over 213).

If is displayed, the drain pump will operate to drain
the water automatically.

If you press the START/PAUSE button when an error is displayed, any error except

will

disappear and the machine will go into the pause status.
In case of

,

,

if the error is not resolved within 20 sec., or the in case of other errors,

if the error is not resolved within 4 min., power will be turned off automatically and the error code will
blink. But in the case of

, power will not be turned off.

«
...
21
22
23
24
25
...
»

Содержание 796.4102#90#































































Отзывы:

Нет отзывов

Похожие инструкции для 796.4102#90#

Бренд: Midea Страницы: 10

DISHDRAWER DD60DHI9

Бренд: Fisher & Paykel Страницы: 19

Бренд: Lett Страницы: 52

Бренд: Indesit Страницы: 68

Бренд: Kärcher Страницы: 58

Бренд: Zanussi Electrolux Страницы: 16

Бренд: CLEANVAC Страницы: 8

Бренд: Admiral Страницы: 32

Performa LAW2400

Бренд: Maytag Страницы: 12

Бренд: Alfa Network Страницы: 20

Бренд: Kärcher Страницы: 196

Porta Stream II

Бренд: U-Line Страницы: 9

HW110-B14979EU1

Бренд: Haier Страницы: 108

Instruments Washer GW2050H

Бренд: Smeg Страницы: 32

ExxcelWVD24520GB

Бренд: Bosch Страницы: 64

Бренд: Bosch Страницы: 60

Бренд: Electrolux Страницы: 14

Бренд: Beko Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды