Kenmore 796.4102#90# Скачать руководство пользователя страница 18

Страница: 18 / 62

5-5. EXPLANATION OF EACH PROCESS

No.

Process

Explanation

Stay

• Electrical power is supplied
• Washer is ready to work and the micom is in the active mode.

Water
supply

• After loading laundry and selecting a course and a cycle, water is

supplied and drum rotates.

• When a user selects Pre-wash course, water is supplied through

pre wash valve.

Soaking
& washing
laundry

• To get laundry wet, drum rotates clockwise and counterclockwise.
• If water amount is insufficient at this time, the Inlet valve will supply

water again.

Heating &
washing

• The heater heats the water in drum to the selected water temperature

and drum rotates for washing.

Washing
& heating
/ washing

• When the water temperature reaches to the selected temperature, the

heating stops and only the drum rotates.

• If water temperature becomes lower than selected because of

re-supplied water, the heating starts again.

Washing

• Fuzzy Logic decides washing time according to the laundry load, water

temperature, and other factors.

Drainage

• A pump motor drains the water from the drum.
• After sensing drained water amount by water level frequency, spin starts.
• When a heating course is selected, stay cooling process is performed to

decrease the water temperature gradually to prevent laundry from being
damaged and for safety reasons.

Untangling
(Sensing
eccent-
ricity)

• It balances laundry load and senses the eccentricity of the load, to only

allow spinning without vibration

• If the eccentricity is worse than the allowed level, it repeats the

disentangling process. When the repeated time is more than allowed
level, it displays UE.

• If the eccentricity is good, the intermittent spin starts.
• During this process, the drain pump works for drainage intermittently.

Содержание 796.4102#90#































































Результаты поиска

Содержание 796.4102#90#

Отзывы:

Похожие инструкции для 796.4102#90#

Бренды по названию

Популярные бренды

Kenmore 796.4102#90#, Руководство по обслуживанию

Результаты поиска

Содержание 796.4102#90#

Отзывы:

Похожие инструкции для 796.4102#90#

Бренды по названию

Популярные бренды