manualshive.com logo in svg

Kenmore 796.4044*9 Series, Руководство по обслуживанию, Страница: 3 / 60

Поделиться
Скачать
Kenmore 796.4044*9 Series Скачать руководство пользователя страница 3

2

CONTENTS

1. SPECIFICATIONS ............................................................................................................... 3

2. FEATURES & TECHNICAL EXPLANATION ....................................................................... 4

3. PARTS IDENTIFICATION  ................................................................................................... 7

4. INSTALLATION AND TEST  ................................................................................................ 8

5. OPERATION ...................................................................................................................... 11

5-1. CONTROL PANEL FEATURES  ................................................................................. 11
5-2. CYCLE GUIDE ........................................................................................................... 14
5-3. SPECIAL FUNCTIONS  .............................................................................................. 15
5-4. EXPLANATION OF EACH PROCESS ....................................................................... 16

6. PROGRAM CHART  .......................................................................................................... 18

7. TEST MODE  ..................................................................................................................... 19

7-1. SAFETY CAUTION .................................................................................................... 19
7-2. LOAD TEST MODE  ................................................................................................... 19
7-3. HOW TO CHECK THE WATER LEVEL FREQUENCY  ............................................. 19

8. TROUBLESHOOTING ...................................................................................................... 20

8-1. SAFETY CAUTION .................................................................................................... 20
8-2. ERROR MODE SUMMARY  ...................................................................................... 20
8-3. TROUBLESHOOTING SUMMARY    ..........................................................................22
8-4. TROUBLESHOOTING WITH ERROR ....................................................................... 24
8-5. TROUBLESHOOTING ELSE ..................................................................................... 31

9. COMPONENT TESTING INFORMATION ........................................................................ 36

9-1. FILTER ASSEMBLY (LINE FILTER) .......................................................................... 36
9-2. DOOR LOOK SWITCH ASSEMBLY .......................................................................... 37
9-3. STATOR ASSEMBLY ................................................................................................. 39
9-4. PUMP MOTOR ASSEMBLY ...................................................................................... 42
9-5. INLET VALVE ASSEMBLY ......................................................................................... 43
9-6. HEATER ASSEMBLY ................................................................................................. 44
9-7. THERMISTOR ASSEMBLY ....................................................................................... 45

10. DISASSEMBLY INSTRUCTIONS .................................................................................... 48

11.EXPLODED VIEW  ............................................................................................................ 57

11-1. CABINET AND CONTROL PANEL ASSEMBLY ...................................................... 57
11-2. DRUM AND TUB ASSEMBLY .................................................................................. 58
11-3. DISPENSER ASSEMBLY ........................................................................................ 59

Содержание 796.4044*9 Series





























































Отзывы:

Нет отзывов