19
ENGLISH
General Care & Cleaning
To Clean the Recessed and Contoured Areas of the Cooktop - If a spill
occurs on or in the recessed or contoured areas, blot up spill with an absorbent
cloth. Rinse with a clean, damp cloth and wipe dry.
To Remove and Replace the Surface Burner Caps and Surface Burner
Heads - Remove in the following order: (1st) surface burner grate, (2nd)
surface burner cap, (3rd) surface burner head and (4th) surface burner drip pan
(if equipped).
Reverse the procedure above to replace the surface burner cap, surface burner
head and surface burner drip pans (if equipped). Do not remove any parts
from the cooktop until they have completely cooled and are safe to handle.
Do not operate the surface burners without the surface burner cap and
surface burner head properly in place.
To Clean the Surface Burner Cap, Surface Burner Head and Surface Burner
Drip Pan (if equipped) - Use a soap-filled scouring pad or a mild abrasive
cleanser to clean the surface burner caps, surface burner heads and surface
burner drip pans (if equipped). The ports (or slots) around the burner head must
be routinely cleaned. If residue still remains in these ports, use a small-gauge
wire or needle to clean the slots or holes. For proper flow of gas and ignition of
the burner—DO NOT ALLOW SPILLS, FOOD, CLEANING AGENTS OR ANY
OTHER MATERIAL TO ENTER THE GAS ORIFICE HOLDER OPENING.
ALWAYS keep the surface burner cap and surface burner head in place
whenever a surface burner is in use.
Cleaning the Contoured Well Areas, Burner Cap, Burner Head and Burner Drip Pans (some models)
T
he contoured well areas, burner cap, burner head and burner drip pans (some models) should be routinely cleaned.
Keeping the burner ports clean will prevent improper ignition and an uneven flame. Refer to the following instructions:
Fig. 3
Removing and Replacing the Oven Door
The door is heavy. For safe, temporary storage, lay the door flat with
the inside of the door facing down.
To Remove Oven Door:
1.
Open oven door completely (horizontal with floor - See Fig. 1).
2.
Remove 2 screws located on the inside of the oven door liner (See A Fig. 2)
3.
Insert the 2 screws into the door hinge holes located on the side of the hinge arm, one into
each hinge (See B Fig. 2).
4.
Close oven door until the door stops, (Do not force the door to close any further). The
placement of these screws should keep door open in about a 45 degree position.
5.
Grasp oven door firmly on both sides and slide door up and off hinges at the same angle.
(See Fig. 3)
6.
To clean oven door, follow the instructions in the General Care & Cleaning table.
To Replace Oven Door:
1.
Be sure the hinge arms remain at the 45 degree angle position. Be sure the screws are
still locking the hinge arms from moving. If the screws fall out of the hinge holes, the
hinge(s) may snap back against the oven frame and could pinch fingers or chip the
porcelain finish on the oven front frame.
2.
Hold door at the sides near the top while resting the lower front of door on your knee. Insert
the door channels at the bottom of door over the door hinges, (See Fig. 3).
3.
Allow the door to slide down into the door hinges evenly at the same 45 degree angle. The
hinge arms should be inserted into the bottom corners as far as they can go.
4.
Open door completely (horizontal with floor) and remove both screws from holes in door
hinges.
5.
Reinstall the 2 screws into the door liner (See C Fig. 2).
6.
If the door is not in alignment with the oven frame, remove door and repeat the above steps.
Fig. 1
Fig. 2
Содержание 790.7185 Series
Страница 6: ...6 Range Features Note The features of your range will vary according to model ...
Страница 24: ......
