Kenmore 625.75116 Скачать руководство пользователя страница 25

Страница: 25 / 26

Questions? Call the Kenmore Water Line 1-800-426-9345 or visit www.kenmorewater.com

Key

No. Part No.

Description

7338111

Screw, #6-19 x 3.5 mm (2 req.)

7281291

Motor

7337474 Motor Mount

53 7284964 Cam & Gear

7030713 Switch

–

7331240 Drain Hose Adaptor Kit

(incl. Key Nos. 55-59)

Clip, Drain

Adaptor, Drain Hose

Hose Clamp

O-Ring, 15.9 x 20.6 mm

Flow Plug, 3.4 lpm

–

7129716 Seal Kit (includes Key Nos. 60-65)

O-Ring, 11.1 x 15.9 mm

O-Ring, 19.1 x 23.8 mm

O-Ring, 85.7 x 92.1 mm

Rotor Seal

O-Ring, 9.5 x 14.3 mm

Seal, Nozzle & Venturi

66 7082087 Bearing, Wave Washer

7199232 Rotor & Disc

–

7342665 Drain Plug Kit, 3/4”

(includes Key Nos. 64, 68 & 69)

Plug, Drain Seal

Spring

7337563 Clip, 3/4”, pack of 4

7342673

Installation Adaptor, 3/4”, pack of

2, including 2 ea. Clips & O-Rings

(See Key Nos. 70 & 72)

7337571 O-Ring, 23.8 x 30.2 mm, pack of 4

Not illustrated.

Not included with water softener.

Valve Parts List

Key

No. Part No.

Description

–

7113040

Turbine & Support Assembly,

including 2 O-Rings (See Key No.

72 ) & 1 ea. of Key Nos. 73 & 74

Turbine Support & Shaft

Turbine

7082053 Valve Body

7081201 Retainer, Nozzle & Venturi

77 7342649 O-Ring, 6.4 x 9.5 mm, pack of 2

1202600 Nut - Ferrule

–

7238450 Nozzle & Venturi Assembly

(includes Key Nos. 76, 77 & 79-87)

7081104 Housing, Nozzle & Venturi

80 7095030 Cone Screen

1148800 Flow Plug, 1.1 lpm

7187772 Nozzle & Venturi Gasket Kit

7204362 Gasket (only)

0521829 Flow Plug, 0.1 gpm

7146043 Screen

7167659 Screen Support

7170262 O-Ring, 28.6 x 34.9 mm

7199729 Cap

88 7309803 Wire Harness (Sensor)

7337466 Valve Cover

90 7342657 Screw, #10-14 x 5 cm, pack of 5

7254260

Installation Adaptor Kit, 3/4”

(includes 2 ea. copper tubes, nuts,

clips & washers)

75537

Bypass Valve Assembly, 3/4”, in -

cluding 2 O-Rings (See Key No. 72)

75533

Drain Tubing, 9.5 mm I.D. x

6 meters

7123613

Silicone Grease (for O-Rings)

42-34405 Flexible Connectors, 3/4”

42-34407 Flexible Connectors, 1”

Содержание 625.75116



























Результаты поиска

Содержание 625.75116

Отзывы:

Похожие инструкции для 625.75116

Бренды по названию

Популярные бренды

Kenmore 625.75116, Инструкция по использованию и уходу

Результаты поиска

Содержание 625.75116

Отзывы:

Похожие инструкции для 625.75116

Бренды по названию

Популярные бренды