manualshive.com logo in svg

Kenmore 625.75116, Инструкция по использованию и уходу, Страница: 13 / 26

Поделиться
Скачать
Kenmore 625.75116 Скачать руководство пользователя страница 13

13

Questions? Call the Kenmore Water Line 1-800-426-9345 or visit www.kenmorewater.com

Programming the Softener

hold for immediate

Low Salt

Select

press for tonight

Figure 15

REGENERATION button

SELECT button

LOW SALT indicator

Display

UP button

DOWN button

PROGRAM THE SOFTENER

When the power supply is plugged into the electrical

outlet, the model code (150) and a test number (exam-

ple: J3.0), are briefly shown in the display.  Then the

words “SET TIME” appear and 12:00 PM begins to flash.

Figure 17

Figure 18

Figure 16

SET PRESENT TIME OF DAY

I

f the words “SET TIME" do not show in the display,

press the SELECT button a few times until they do.

1

. Press the 

r

UP or 

s

DOWN buttons to set the

present time.  Up moves the display ahead; down

sets the time back.  Be sure AM or PM is correct.

NOTE:

Press buttons and quickly release to slowly

advance the display.  Hold the buttons down for

fast advance.

2

. When the correct time is displayed, press the SELECT

button, and the display will change to show the

“Hardness” screen.

SET WATER HARDNESS NUMBER

If you completed the previous step, the words “SET

HARD NESS" should show in the display.  Otherwise,

press the SELECT button several times until they do.

1

. Press the 

r

UP or 

s

DOWN buttons to set the

hardness of your water supply, in grains per gallon.

The default is 25.

NOTE: If your water supply contains iron

, compensate

for it by adding to the water hardness number.

For example, assume your water is 20 gpg hard

and contains 2 ppm iron.  Add 5 to the hardness

number for each 1 ppm of iron.  In this example,

you would use 30 for your hardness number.

20 gpg hardness

2 ppm iron x 5 = 10

+10

(times)

30 HARDNESS NUMBER

If your water supply contains iron, it is recom-

mended that you clean your water softener resin

bed at least every 6 months.  Your local Sears

store has Water Softener Cleaner (Part Number

75534) available.

2

. When finished setting your water’s hardness number,

press the SELECT button, and the display will change

to show the “Set Recharge Time” screen.

continued on next page

Содержание 625.75116



























Отзывы:

Нет отзывов