Kenmore 625.348420 Скачать руководство пользователя страница 12

Страница: 12 / 32

HOW YOUR WATER SOFTENER WORKS

SECTION 2

2B. SOFT WATER SERVICE AND REGENERATION

BRINING:

During brining, thebrineis moved

from thesalt storagearea, into theresin tank. Inside

the resin tank, brine cleans hardness minerals from

the resin beads and they are discharged out the

drain. How much brine is needed to clean the resin

depends on:

the amount of resin in the softener,

-- how fast thebrinegoes through thebed.

Thenozzleand venturi (FIG. 6) makesuction to

movebrinefrom thesalt tank into theresin tank.

They keep the brine flow down to a very slow rate to

get the best resin cleaning with the least salt.

BRINE RINSE:

After all of thebrineis sucked out

of thesalt tank, thebrinevalvecloses. Water keeps

flowing through theresin tank thesameway it did

during brining except the brine flow has stopped.

Hardness minerals and brine flush from the resin

tank to thedrain. Brining and brinerinsetogether

vary in length of time they take, relative to the fill

cyclelength.

FIG. 6

WATER FLOW THROUGH THE
SOFTENER IN BRINING AND
BRINE RINSE

ÏÏÏÏÏÏÏ

ÌÌÌ

hard water
IN

hard water

bypass OUT

brine valve

drain

nozzle &
venturi

brine

BACKWASH:

During backwash, water flows UP

through theresin tank (FIG. 7) at a fast rateto flush

iron minerals, dirt and sediments from the bed and to

the drain. The bed lifts and expands for good

cleaning.

FIG. 7

WATER FLOW THROUGH THE
SOFTENER IN BACKWASH

ÏÏÏÏÏÏ

ÌÌÌ

hard water
IN

hard water

bypass OUT

drain

resin bed lifted
and expanded

FAST RINSE:

Backwash is followed by a fast flow

of water down through the resin tank. The fast flow

packs the resin bed and gets it ready for return to

service (FIG. 8).

After fast rinse, the softener returns to service. Hard

water goes into the resin tank where the resin bed

again takes out the hardness minerals. Soft water

goes to the house soft water pipes.

FIG. 8

WATER FLOW THROUGH THE
SOFTENER IN FAST RINSE

ÏÏÏÏÏÏ

ÌÌÌ

soft water

OUT

drain

hard water
IN

Содержание 625.348420

































Результаты поиска

Содержание 625.348420

Отзывы:

Похожие инструкции для 625.348420

Бренды по названию

Популярные бренды

Kenmore 625.348420, Руководство пользователя

Результаты поиска

Содержание 625.348420

Отзывы:

Похожие инструкции для 625.348420

Бренды по названию

Популярные бренды