Kenmore 415.162080 Скачать руководство пользователя страница 26

Страница: 26 / 28

26 • 463843104

Troubleshooting - Electronic Ignition System

Problem

No sparks appear at
any electrodes when
ignition button is
pushed; no noise can
be heard from spark
module.

No sparks appear at
any electrodes when
ignition button is
pushed; noise CAN be
heard from spark
module.

Sparks are present but
not at all electrodes
and/or not at full
strength.

Possible Cause

• Battery not installed

properly.

• Dead battery.

• Button assembly not

installed properly.

• Faulty spark module.

• Output lead

connections not
complete.

• Output lead

connections not
complete.

• Arcing to grill away

from burner(s).

• Weak battery.

• Electrodes are wet.

• Electrodes cracked or

broken “sparks at
crack”.

Prevention/Solution

• Install battery (make sure that “+” and “—” connectors

are oriented correctly, with “+” end down and “—” end
up.)

• Replace battery with new AAA-size alkaline battery.

• Unscrew button cap assembly and reinstall, making sure

threads are aligned and engaged fully.

• Replace spark module assembly.

• Remove and reconnect all output connections at module

and electrodes.

• Remove and reconnect all output connections at module

and electrodes.

• If sparks are observed other than from burner(s), wire

insulation may be damaged. Replace wires.

• Replace battery with a new AAA-size alkaline battery.

• Use paper towel to remove moisture.

• Replace cracked or broken electrodes.

Check Procedure

• Check battery

orientation.

• Has battery been

used previously?

• Check to insure

threads are properly
engaged. Button
should travel up and
down without binding.

• If no sparks are

generated with new
battery and good wire
connections, module
is faulty.

• Are output

connections on and
tight?

• Are output

connections on and
tight?

• If possible, observe

grill in dark location.
Operate ignition
system and look for
arcing between
output wires and grill
frame.

• All sparks present but

weak or at slow rate.

• Has moisture

accumulated on
electrode and/or in
burner ports.

• Inspect electrodes for

cracks.

Содержание 415.162080





























Результаты поиска

Содержание 415.162080

Отзывы:

Похожие инструкции для 415.162080

Бренды по названию

Популярные бренды

Kenmore 415.162080, Инструкция по сборке

Результаты поиска

Содержание 415.162080

Отзывы:

Похожие инструкции для 415.162080

Бренды по названию

Популярные бренды