background image

463843104 • 17

DANGER

USE AND CARE

• Never fill the cylinder beyond 80% full. An overfilled

spare LP tank is hazardous due to possible gas
released from the safety relief valve.

• The safety relief valve on the LP tank could activate,

releasing gas and cause an intense fire with risk of
property damage, serious injury or death.

• NEVER store a spare LP tank under or near grill or in

enclosed areas.

• If you see, smell or hear escaping gas, immediately get

away from the LP tank/grill and call your fire
department.

• All spare LP tanks must have safety caps installed on

the LP tank outlet.

LP Tank Removal, Transport And Storage

• Turn OFF all control knobs and LP tank valve. Turn coupling

nut counterclockwise by hand only - do not use tools to
disconnect. Lift LP tank wire upward off of LP tank collar, then
lift LP tank up and off of support bracket. Install safety cap onto
LP tank valve. Always use cap and strap supplied with valve.

Failure to use safety cap as directed may result in serious
personal injury and/or property damage.

LP Tank Valve

Retainer Strap

Safety Cap

• A disconnected LP tank in storage or being transported must

have a safety cap installed (as shown).

• Do not store an LP tank in enclosed spaces such as a carport,

garage, porch, covered patio or other building. Never leave an
LP tank inside a vehicle which may become overheated by the
sun.

• Do not store an LP tank in an area where children play.

LP Tank

• The LP tank used with your grill must meet the following

requirements:

Use

only LP tanks equipped with this type of valve.

Use LP tanks only with these required measurements: 12"
(30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.)
capacity maximum.

• LP tanks must be constructed and marked in accordance with

specifications for LP tank of the U.S. Department of
Transportation (DOT). See LP tank collar for marking.

LP tank valve must have:
• Type 1 outlet compatible with

regulator or grill.

• Safety relief valve.
• UL listed Overfill Protection

Device (OPD). This OPD safety
feature is identified by a unique triangular hand wheel.

• LP tank must be arranged for vapor withdrawal and include

collar to protect LP tank valve.

OPD Hand Wheel

LP (Liquefied Petroleum Gas)

For

Your Safety

LP gas is nontoxic, odorless and colorless when produced.

, LP gas has been given an odor (similar to rotten

cabbage) so that it can be smelled.

LP gas is highly flammable and may ignite unexpectedly when
mixed with air.

LP Tank Filling

must purge tank

NEVER

Use only licensed and experienced dealers.

LP dealer

before filling.

Dealer should

fill LP tank more than 80% of LP tank

volume. Volume of propane in tank will vary by temperature.

A frosty regulator indicates gas overfill. Immediately close LP
tank valve and call local LP gas dealer for assistance.

• Do not release liquid propane (LP) gas into the atmosphere.

This is a hazardous practice.

• To remove gas from LP tank, contact an LP dealer or call a

local fire department for assistance. Check the telephone
directory under “Gas Companies” for nearest certified LP
dealers.

Содержание 415.162080





























Отзывы: