background image

安全上のご注意

◆天体望遠鏡をご使用の前に◆

4

SAFETY PRECAUTION

This section covers the assembly instructions for your New Moon Light II telescope. It is highly recommended 

that the first setup of the telescope should be done indoors. This way it will be easier to identify all the various 

parts and familiarize yourself with the correct assembly procedure before attempting out in the field.

1.Setting Up the Tripod

Stand the tripod upright and pull the tripod legs 

apart until each leg is fully extended (Fig-1). As 

necessary, adjust the leg-length releasing the tripod 

extender lock (Fig-2).

3.Attaching the Finder to the Telescope 

Optical Tube

Attach the finder to the proper location on the 

telescope optical tube. The finder should be aligned 

before using the telescope (See page 5 for proper 

aligning of the finder.).

4.Installing the Eyepiece

To observe an erect image with the telescope, you 

must use an eyepiece. Attach the eyepiece with the 

star diagonal like shown on the picture below and 

tighten the locking screws.

2.Attaching the Telescope Optical Tube to 

the Tripod

Place and fix the telescope optical tube on the 

tripod using the telescope-tube locking screw. At 

this time, make sure to fit the concave part of the 

telescope tube and the convex part of the mount so 

that the tube is aligned properly.

NOTE: Attaching the telescope optical tube to the 

tripod mount should be firmly secured. It is danger-

ous if the tubes fall off caused by an unsecured 

locking screw.

Adjust the height of tripod by extending the 

elevator part by loosening the elevator locking 

screw.

The eyepiece can be changed to different powers. 

This telescope comes with two eyepieces. 

Depending on the observed object, you can select 

your favorite eyepiece.

Examples:When New MoonLight II with 20mm 

eyepiece is used:

How to calculate the Powers of Telescope

(Fig-1)

(Fig-2)

Tripod Extender Lock

Telescope Optical Tube

Telescope Optical Tube

Finder

Eyepiece

Diagonal

Locking 

Screw

Mounting 

Image

Tripod Mount

Telescope-tube

Locking Screw

Focal Length of Objective Lens in (mm)

Focal Length of Eyepiece in (mm)

= X Powers of Telescope

360(mm)

20 (mm)

=18xPowers

Содержание New Moonlight II









Отзывы: