kENDALL SCD EXPRESS Скачать руководство пользователя страница 17

Страница: 17 / 24

EN-14

Power Supply Board (Removal / Installation)

CAUTION:

Use a grounded strap when handling any electronic components.

• The power supply has no user serviceable parts except for the fuses. No attempt should be made to repair a damaged supply. Return to the factory for

repair or replacement.

• Disconnect the 4-pin controller board wiring harness from the power board.

• Remove the muffler as described in “Muffler (Removal/Installation).”

• The power supply board is held in place by channels on the side of the rear case as well as retaining brackets on the front case.

• To remove the power board slide the board out from the rear case.

• Installation is the reverse of removal.

Fan and Screen (Removal / Installation)

• Disconnect the 2-pin fan connector from the power board.

• Observe the angle and orientation of the fan and screen prior to removal to ease reassembly. (Diagram 04)

• Slide the fan and screen out of the case by pulling straight out.

• Installation is the reverse of removal. For optimum cooling and quietness, use only Kendall replacement fans.

Main Controller Board (Removal/Installation)

CAUTION:

Use a grounded strap when handling any electronic components.

• The main CPU board has no user serviceable parts. No attempt should be made to repair a damaged board. Return to the factory for repair or

replacement.

• Disconnect the 4 pin controller board wiring harness from the power board.

• The main CPU board is located on the front cover and is held in place with two screws.

• Disconnect the two membrane ribbon cables by sliding them out of the connectors on the controller board.

• Remove the controller board.

• Installation is the reverse of the removal.

Содержание SCD EXPRESS

























Результаты поиска

Содержание SCD EXPRESS

Отзывы:

Похожие инструкции для SCD EXPRESS

Бренды по названию

Популярные бренды

kENDALL SCD EXPRESS, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание SCD EXPRESS

Отзывы:

Похожие инструкции для SCD EXPRESS

Бренды по названию

Популярные бренды