Kendal Lighting AC-22452, Инструкция по установке и эксплуатации

Страница: 9 / 9

4. CONNECTING THE RECEIVER (FIG.2)
5. INSTALLING THE WIRELESS WALL TRANSMITTER
. OPERATING THE TRANSMITTER
8
Use the wire nuts provided and make electrical connections as follows:
a. Connect Green wire from fan to the Bare copper (ground) from junction box.
b. Connect Black wire (AC IN L) from the Receiver to the Black wire from the
junction box.
c. Connect White wire (AC IN N) from the Receiver to the White wire from junction box.
d. Connect Black wire (TO MOTOR L) from the Receiver to the Black wire from fan.
e. Connect White wire (TO MOTOR N) from the Receiver to the White wire from fan.
f. Connect Blue wire (FOR LIGHT) from the Receiver to the Blue wire from fan.
g After wires are connected, carefully tuck them into the junction box.
h. Lay the black antenna wire on top of the Receiver and insert into the mounting bracket.
i. Reinstall the canopy onto the mounting bracket.
.
#8
Remove the small panel on the front of the transmitter and insert the battery provided. Make
sure the “ + ” “ - ” sigh is correct. (FIG.3)
NOTE: Use 1x12V (23A) battery. If not using for long period of time, remove battery to prevent
damage to transmitter.
a. “ HI ” button: this button used to select the fan at high speed.
b. “ MED ” button: this button used to select the fan at medium speed.
c. “ LOW “ button: this button used to select the fan at low speed.
d. “ OFF ” This button will turn the fan off.
e. “ LIGHT ” This button will turn the light on or off and will also control the brightness setting.
Press and release the button and the light will turn on or off. Press and hold the button for
the desired brightness.The light will cycle continuously between bright and dim settings as
long as the button is held down. The light key has auto resume, it will stay at the same
brightness as last time when it was turned off.
f. Memory function
If you turn off the fan or light by wall control, it will memorize and recover automatically to
last time ’ s fan speed and light brightness when turned on next time.
g.Light on/off and dimmer select.
There is a dip swith in the plate.(fig 1), this swith used to select the light mode, If this swith
select “ D ” , The light in the dimming mode. If this switch select “ ON ” , the light in the “ ON/OFF ”
mode.
.
a
b.
c.
.
6
. INSTALLING THE BATTERY INTO THE TRANSMITTER(FIG.4)
7
(FIG.3)
RECEIVER PROTECTIVE FUNCTIONS
Remove the existing wall plate and switch.Be sure to complete the electrical circuit within
the junction box by-passing wall control. Connect black to black, white to white, green to
green. Carefully push wires into the outlet box.
Attach wall control unit to outlet box using the two -32 screws provided.
Attach wall plate to the switch control front using the two small screws provided.
a. Over load protection (current limit)- The device limits the maximum current output from the
receiver/drive when the fan or light load is increased abnormally. The fan will shut off if over
lamped.
CEILING FAN WALL TRANSMITTER CONTROLLER
WARNING! SHUT OFF THE POWER WITH FUSE OR CIRCUIT BREAKER.
1. SAFETY PRECAUTIONS:
WARNING: HIGH VOLTAGE:
Disconnect the electric power source by removing
fuse or switching off circuit breakers.
Do not use with solid state fans.
Electrical wiring must meet all local and national electrical code requirements.
Electrical source and fan must be 115/120 volt, 60Hz. Maximum fan motor 1A, Maximum
light watts: 60W LED only.
Household electric power can cause serious injury or death.
a. Turn the power off to your ceiling fan.
b. Return power to the receiver.
NOTE: After the AC power is on, do not press any other button on the wall transmitter
before pressing the “ SET ” button(in the small plate), doing so will cause the
procedure to fail.(Fig.1)
c. Within 60 seconds of turning the fan ’ s AC power on, Press and hold the transmitter ’ s
“ SET ” button for 3 seconds.
d. Once the receiver has detected the set frenquency, the light of your fan if applicable
will blink twice.(There is no indication if your fan is not equipped with a light)
e. The receiver has now learn the frequency with the wall transmitter. After completing
the steps above, you should be able to operate the ceiling fan and light. If the fan is
not responding to the transmitter, Please turn the power off to the receiver, and repeat
the process.
2.
FREQUENCY INTERFERENCE.
3. INSTALLING THE RECEIVER
a. Remove the ceiling fan canopy from the mounting bracket.
b Disconnect the existing wiring between ceiling fan and the junction box.
.
NOTE:
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference;
(2) This device must accept any interference received, including
interference that may cause undesired operation .
FIG.3
FIG.4
12V(23A)
Battery
12V
HI
L
OW
OFF
L IGHT
TO MOTOR L
TO MOTOR N
FIG.2
FIG.1
AC8-LED-DCW-2160414
SET D
ON
MED
HI
L OW
OFF
L
IGHT
MED
12V
SET D
ON
SET
D
ON
TO MOTOR L
TO MOTOR N
H
Z