Kelvinator 10DF-13 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 40

Kelvinator 10DF-13 Скачать руководство пользователя страница 6

Grounding Instructions

This appliance is equipped with a three-prong (ground-
ing) plug for your protection against shock hazards. The
appliance should be plugged directly into a properly
grounded three-prong receptacle.

Where a two-prong wall receptacle is encountered, it
must be replaced with a properly grounded three-prong
receptacle in accordance with the National Electrical
Code and local codes and ordinances. The work must
be done by a licensed electrician.

IMPORTANT

Do not, under any circumstances cut or remove the
round grounding prong from the appliance plug.

WARNING

Consult a licensed electrician if you have any
doubt about the grounding of your wall
receptacle. Only a licensed electrician can
determine the polarization of your wall
receptacle. Only a properly installed three-
prong wall receptacle assures the proper
polarization with the appliance plug.

4

GROUNDING INSTRUCTIONS

20 Amp

15 Amp

15 Amp

20 Amp

«
...
4
5
6
7
8
...
»

Содержание 10DF-13









































Отзывы:

Нет отзывов