Keithley KPCMCIA-12AIAOH Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 58

Keithley KPCMCIA-12AIAOH Скачать руководство пользователя страница 55

C-20

I/O Registers

KPCMCIA-12AIAOH User’s Manual

Auxiliary status register (base + 15, read only)

Bits 0 to 3 and bit 7 in this register are organized for bits in the status register (base + 2) and can
be referenced without the associated side effect of “clear after read” on the latched events. Back-
ward compatibility is kept by preserving the “clear after read” side effect for the status register in
KPCMCIA-12AIAOH PC cards.

Refer to Table C-19. Bits 0 and bit 1 are the data FIFO flags exactly as in the status register. Bit
2 in this register is the data lost event latch, as is bit 5 in the status register. These three bits are
defined exactly the same as in the status register.

Bit 3 in this register is the logic OR of the two event latches in the status register; i.e., the EOS
event latch and the data FIFO event latch. This bit is 1 if either EOS or FIFO event is latched. It
is 0 if both EOS and FIFO events are cleared (by power up, reset, or reading the status register).

Bit 4 indicates the timer/counter overflow event. It is 1 each time the timer/counter overflow
occurs (actually on the next rising edge of the select clock source after it reaches the final count).
This bit is not cleared by reading the auxiliary status register. It can only be cleared by writing a
0 into bit 5 of the auxiliary control register. Refer to Section 3 and “Timer/counter port (base +10,
base +11)” in this section for more information.

Bit 5 tells whether the D/A port buffer register is occupied (1) or empty (0). Refer to Section 3 or
“D/A data port (base +8, base +9)” in this section for more information.

With the pre-trigger option selected, bit 6 is set to 1 when the external trigger comes. It remains
1 until the data acquisition is terminated by receiving the A/D stop command. Refer to “Stop
A/D command.” Bit 6 of 0 means the trigger has not activated yet. If the pre-trigger option is not
selected (or bit 6 of the auxiliary control register is 0), this bit should be ignored.

Bit 7 is exactly the same as bit 6 in the status register (base + 2, read only). Refer to “Status
register (base +2, read only)” for more information.

Table C-19

Auxiliary status register bit definitions

Bit

Function

Explanation

7

A/D running flag

1 = Running, 0 = Idle

6

A/D trigger flag

1 = Triggered, 0 = Not yet

5

D/A port buffer register flag

1 = Occupied, 0 = Empty

4

Timer/counter overflow event latch

1 = Overflow latched, 0 = Not yet

3

A/D conversion event latched (logic
“OR” of A/D EOS and FIFO almost-
full event latches)

1 = Either EOS or FIFO almost-full
event has been latched
0 = Neither event has been latched yet

2

Data lost event latch

1 = Data lost latched, 0 = Not yet

1

A/D data FIFO almost-full flag

1 = FIFO almost full, 0 = Not yet

0

A/D data FIFO empty flag

1 = FIFO empty, 0 = Not empty

«
...
53
54
55
56
57
...
»

Содержание KPCMCIA-12AIAOH



























































Отзывы:

Нет отзывов