Keithley 7701 Скачать руководство пользователя страница 32

Страница: 32 / 33

Model 7701 27

GENERAL

32 CHANNELS: 32 channels of 2-pole relay

input. All channels configurable to 4-
pole.

RELAY TYPE: Latching electromechanical.

ACTUATION TIME: <3ms.

FIRMWARE: Specified for Model 2700 rev.

B03 and Model 2750 rev. A01.

DMM CONNECTIONS: Screw terminals

provide internal DMM connections to
channels 34 and 35 and connections to
external wiring access.

CAPABILITIES

CHANNELS 1–32: Multiplex one of 32 2-

pole or one of 16 4-pole signals into
DMM. Configuration supports dual
1

16 independent multiplexers.

INPUTS

MAXIMUM SIGNAL LEVEL: Any channel

to Any Channel (1–32): 150V DC or
150Vrms (212V peak) for AC waveforms,
1A switched, 60W, 125VA maximum.

SAFETY: Conforms to European Union

Directive 73/23/EEC EN61010-1, CAT I.

CONTACT LIFE (typ):

>10

operations at max signal level.

>10

operations cold switching.

CONTACT RESISTANCE: <1

Ω

any path

and additional 1

Ω

at end of contact life.

CONTACT POTENTIAL: <6µV per contact

pair.

OFFSET CURRENT: <100pA.

CONNECTOR TYPE: 50-pin female D-shell, Channels 1–24. 25-pin female D-shell, Channels 25–32. Supplied with male IDC ribbon cable con-

nectors.

ISOLATION BETWEEN ANY TWO TERMINALS: >10

Ω

, <200pF.

ISOLATION BETWEEN ANY TERMINAL AND EARTH: >10

Ω

, <400pF.

CROSS TALK (1MHz, 50

Ω

Load): <–35dB.

INSERTION LOSS (50

Ω

Source, 50

Ω

Load): <0.35dB below 1MHz. <3dB below 2MHz.

COMMON MODE VOLTAGE: 300VDC or 300Vrms (425V peak) for AC waveforms between any terminal and chassis.

ENVIRONMENTAL:

OPERATING ENVIRONMENT: Specified for 0°C to 50°C. Specified to 50% R.H. at 35°C.

STORAGE ENVIRONMENT: –25°C to 65°C.

WEIGHT: <0.52kg (1.16 lb).

ACCESSORIES AVAILABLE:

Model 7789 50/25 Pin Male D-Shell Solder Cup Connectors
Model 7790 50/50/25 Pin Female/Male D-Shell IDC Connectors

Specifications subject to change without notice.

Channel 1

Channel 16

(Channels 2–15)

Channel 17

Channel 32

(Channels 18–31)

Backplane
Isolation

DMM Input

Channel 33

2-Pole (Open)
4-Pole (Closed)

(see Note)

To
Internal
DMM

NOTE Channels 33–35 in this schematic refer to the designations

used for control and not actual available channels.

For more information, refer to the ROUTE:MULT command
section in the Model 2700 or 2750 User’s Manual.

Channel 35

(see Note)

Channel 34

(see Note)

Multiplexer 1

Screw

Terminals

Screw

Terminals

The Model 7701 is rated for low-voltage applications.
When connecting the 7701 to the internal DMM via
the screw terminals, all other modules in the
mainframe must be derated to 150VDC or 150Vrms
(212V peak) for AC waveforms.

DMM Sense

Multiplexer 2

External
Wiring Access

User
Configurable
Screw
Terminals

MODEL 7701 SPECIFICATIONS

Содержание 7701


































Результаты поиска

Содержание 7701

Отзывы:

Keithley 7701, Руководство пользователя, Страница: 32 / 33

Результаты поиска

Содержание 7701

Отзывы: