Keithley 7016A Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 20

Keithley 7016A Скачать руководство пользователя страница 18

Connections and Installation

2-5

2.4.1 Card installation

Perform the following steps, and refer to Figure 2-5 or Figure
2-6 to install the card assembly in the Model 7001/7002
mainframe.

WARNING

Turn off power to all instrumentation
(including the Model 7001/7002), and
disconnect all line cords. Make sure all
power is removed and any stored energy
in external circuitry is discharged.

1. Open the ejector arms at the back edge of the card.
2. Slide the card edges into the guide rails inside the main-

frame.

3. Carefully push the card all the way forward until the

ejector arms engage the mounting cups.

4. Push in on the card edge and ejector arms until the card

is properly seated.

5. Make sure the ejector arms are properly latched.

2.4.2 Card removal

Follow the steps below to remove the multiplexer card from
the mainframe:

WARNING

Turn off power to all instrumentation
(including the Model 7001/7002), and
disconnect all line cords. Make sure all
power is removed and any stored energy
in external circuitry is discharged.

1. Pull out on the ejector arms until the card pulls free from

the internal connector.

2. Carefully slide the card out of the switching mainframe.

Figure 2-5

Card installation in Model 7001

Unlock card

Lock card

Ejector Arms (2)

«
...
16
17
18
19
20
»

Содержание 7016A





















Отзывы:

Нет отзывов