background image

Model 6517A Getting Started Manual

Measurement Options

2-11

Zero check

With zero check enabled (“ZeroCheck” displayed), the input signal is routed to low 
through a high impedance shunt. For volts, amps, and ohms measurements, zero check 
should be enabled when connecting or disconnecting input signals. For charge measure-
ments, zero check should be disabled. If left enabled, the charge will dissipate through the 
10M

 shunt.

The Z-CHK key is used to enable and disable zero check.

NOTE

To ensure proper operation, always enable zero check before changing functions 
(V, I, R, or Q).

Zero correct

The Z-CHK and REL keys work together to cancel (zero correct) any internal offsets that 
might upset accuracy for voltage and current measurements.

Perform the following steps to zero correct the volts or amps function:

1.

Select the V or I function.

2.

Enable Zero Check.

3.

Select the range that will be used for the measurement, or select the lowest range.

4.

Press REL to zero correct the instrument. The REL indicator turns on and the 
“ZCor” message is displayed.

NOTE

For the volts function, the “ZCor” message will not be displayed if guard was 
already enabled (“Grd” displayed).

5.

Press Z-CHK to disable zero check.

6.

Readings can now be taken in the normal manner.

NOTES

The instrument will remain zeroed even if the instrument is upranged. If down-
ranged, re-zero the instrument.

To disable zero correct, first enable zero check and then press REL.

Содержание 6517A









































































































Отзывы: