manualshive.com logo in svg

Keithley 2002, Руководство по ремонту, Страница: 85 / 148

Поделиться
Скачать
Keithley 2002 Скачать руководство пользователя страница 85

Troubleshooting

2-72

2.11.18 Absolute value circuit X1 gain tests

Test 404.1 — Absolute value X1 gain, - full-scale DAC

Type

Pass/Fail

Fault message

Absolute value gain = 1

Description

DAC U433 and op amp pair U430 are set up to generate -4.36 VDC at and tied to
ACF through R491 and U412. ACF is tied to AMP IN through U428, Q422, and the ACV buffer.
AMP IN is tied to the inverting and non-inverting paths of FWR. NETOUT from U417 in the
non-inverting path is monitored by the ZERO CROSSING amp for positive or negative polarity
of the input signal and generates the COMP- signal that is fed to comparator U408. The com-
parator selects the path that the AMP IN signal will follow through the FWR with switches
U410. The minus AMP IN path is through the inverting path R452, U418, U410, Q404, and
U419 to pin 12 of the U414 multiplexer. The output of the multiplexer is tied to the A/D through
buffer U403, ACV/A input to U222, and the A/D buffer in the X1 gain configuration.

Drawing reference

Analog Board; 2002-100

Components

U403, U417, U418, U419, U428, U430, U433, and associated components.

Bit patterns

Test 404.2 — Absolute value X1 gain, - half-scale DAC

Type

Pass/Fail

Fault message

Absolute value gain = 1

Description

DAC U433 and op amp pair U430 are set up to generate -2.15 VDC at . This signal
follows the same path as test 404.1.

Drawing reference

Analog Board; 2002-100

Components

U403, U414, U417, U418, U419, U428, U430, U433, and associated components.

Bit pattern*

Register

—U400—

01011100

—U811—

00001101

—U224—

00010111

—U432—

00010111

—U810—

00000011

—U206—

01110000

—U203—

10001110

—U411—

11111011

—U809—

11100111

—U207—

11001111

—U221—

11101001

—U406—

01001101

AD_STB

MUX_STB

R1_STB

R2_STB

*Bits associated with register IC terminals as follows:
Q

Q

Q

Q

Q

Q

Q

Q

87654321

87654321

87654321

87654321

IC pins: Q8=11, Q7=12, Q6=13, Q5=14, Q4=7, Q3=6, Q2=5, Q1=4.

Содержание 2002





















































































































































Отзывы:

Нет отзывов