manualshive.com logo in svg

Keithley 2002, Руководство по ремонту, Страница: 38 / 148

Поделиться
Скачать
Keithley 2002 Скачать руководство пользователя страница 38

 

Troubleshooting

 

2-25

 

Test 201.1 — Test cal zero

 

Type

 

Pass/Fail

 

Fault message

 

None

 

Description

 

U222 is set up to switch common through R259 and S1 pin 4 input to the A/D buffer U226. U226
is set up for X1 gain through U227 pin 2 to 3 with /X1 pin 1 low. Also, common is switched
through R312 and U242 pins 2 to 3, through R311 and to pin 3 of U253. U253 is the buffer for
ADGND. ADGND is routed to A/D_IN through the parallel combination of R285 and R286.
Common is the input to A/D_IN. Zero reading is acquired and stored for Testcal. 

This test is performed by measuring for 0V at A/D_IN.

 

Drawing reference

 

Analog Board; 2002-100

 

Components

 

Switching paths for signals and A/D converter.

 

Bit patterns

Test 201.2 — 7 Volt reference

Type

Pass/Fail

Fault message

Cannot measure 7V at A/D

Description

The 7V reference REFHI generated by U219 and associated circuitry is connected to buffer
U255 to generate REFBUF signal. REFBUF is switched through R263 and U222 pin 5 to U226.
U226 is set up for X1 gain through U227 pin 2 to 3 with /X1 pin 1 low. R274 is the feedback
path of U226. REFLO is switched through R310 and U242 pins 7 to 6, through R311, and to pin
3 of U253. U253 is the buffer for ADGND. ADGND buffer with REFLO signal is connected to
the bottom of the parallel combination of R285 and R286. A/D_IN will be the difference voltage
of REFHI (REFBUF) and REFLO (ADGND). The A/D is triggered and the REFHI reading in
counts is acquired and stored for Testcal. REFHI counts are compared to a by design value of
counts.

Drawing reference

Analog Board; 2002-100

Components

Reference circuit, A/D converter, and the switching paths for the signals.

Bit pattern*

Register

—U400—

01111011

—U811—

00001101

—U224—

00010111

—U432—

10000000

—U810—

00010111

—U206—

01110000

—U203—

10001110

—U411—

11111011

—U809—

01101111

—U207—

00001111

—U221—

11101001

—U406—

00000100

AD_STB

MUX_STB

R1_STB

R2_STB

*Bits associated with register IC terminals as follows:
Q

Q

Q

Q

Q

Q

Q

Q

87654321

87654321

87654321

87654321

IC pins: Q8=11, Q7=12, Q6=13, Q5=14, Q4=7, Q3=6, Q2=5, Q1=4.

Содержание 2002





















































































































































Отзывы:

Нет отзывов