background image

 

Page 19 

 

 

DOC0935 (26 July 2022 12:02) 

www.keit.co.uk 

Back to Table of Contents 

(H) Mounting holes 

The spectrometer must be supported using the four M8 mounting holes in its base. Optional 
feet are provided.  

(I) Power cable gland 

This is the mains power connection to the spectrometer. More detail on how to connect power 
to the spectrometer can be found in Section 2.1 Powering the IRmadillo. 

4.1.1.  Dust caps 

The communication flying leads are provided with dust caps to protect the RJ45 connectors. 
When the cable is not in use, these should be attached to reduce the risk of potential damage 
to the connectors that may be caused by the local environment. 

4.2.  Controller specifications 

Table 3 - Specifications of the IRmadillo integrated controller 

Category 

Specification  

Integrated 
controller 

The integrated controller has been optimised for the rugged operation of 
the IRmadillo spectrometer; it is not a general-purpose personal computer. 
Keit does not recommend the installation of additional software; changes 
to the configuration may affect performance and reliability. 

User 
accounts 

There are two user accounts, one with system administrator privileges and 
a second ‘standard’ user. The standard user account starts automatically 
and is the default account for the KeitSpec software application. The system 
administrator account is provided to make changes to the operating system 
configuration and install additional software, if required. 

Windows 
updates 

The  controller  is  running  Windows  10  LTSC  with  automatic  updates 
disabled  by  default.  The  local  administrator  should  choose  when/if  to 
update  the  operating  system.  A  strategy  will  be  required  to  manage 
updates, particularly if the controller is connected to a network. 

Anti-virus 

There is no anti-virus installed. The controller should only be connected to 
internal, protected networks. Install your preferred anti-virus if required 

 

4.3.  Storage conditions  

When  installed  with  purge  and  power,  the  IRmadillo  can  thermally  control  its  internal 
temperatures up to the limit specified on the product label. However, if the system is to be 
stored before its use Keit recommends an air-conditioned environment. The environment must 
be non-condensing, with a relative humidity below 95%. The IRmadillo or storage container 
should also be out of direct sunlight. 

 

WARNING 

Storing the IRmadillo unpowered and unpurged in unsuitable 
conditions  can  cause  damage  to  the  instrument.  If  in  doubt, 
please consult with Keit  

 

Содержание ASM0627-10-Z-Cx-Ex-Gx-D3x










































Отзывы: