manualshive.com logo in svg
background image

08

AIR300 LEG EXTENSION PRO 

OPERATION MANUAL

INSTALLATION AND PLACEMENT 

TRAINING SPACE

Figure 4. Training Space for the Air300 Leg Extension Pro

The equipment footprint is 40 inches x 39 inches (1,016 
mm x 991 mm). 
The minimum recommended free space around the 
equipment is 24 inches (610 mm) for the front and 
sides.

ASSEMBLY AND PLACEMENT

No assembly required. Place the Air300 Leg Extension 

Pro on a flat, level surface. Make sure the base of the 
frame  makes  full  contact  with  the  floor.  If  gaps  are 

present, relocate the equipment to an even surface.

CONNECT THE EQUIPMENT TO THE KEISER AIR 
SYSTEM

WARNING: Never connect equipment to an air 

source capable of exceeding 120 psi / 8.27 bar.

 

Over pressurizing Keiser pneumatic equipment may 
cause tubing to burst, breakage of equipment, 
abnormal operation, or serious injury. Use only clean, 
dry, regulated compressed air at the rated pressure 
range of 100–120 psi / 6.89–8.27 bar.

1.  Plug the Compressor into the appropriate power 

source to power the Compressor ON

 (allow the 

Compressor to build up to a minimum of 100 psi / 6.89 
bar; Keiser Compressor and Keiser Air System not 
included, sold separately)

.

2.  Connect the 1/4-inch Quick Disconnect (QD) from 

the equipment into the Keiser Air Supply 

(see 

Figure 3)

.

Note: Additional Free Space may be required to accommodate mobility device access.

Figure 3. How to Connect the Equipment to 

the Keiser Air Supply

Keiser Air System

(floor or wall air outlet)

Direct-connect to
Keiser Small Air Compressor

Keiser

Large Air Compressor

Keiser

Small Air Compressor

1/4-inch QD

FREE AREA

24 inches 

(610 mm)

24 inches 

(610 mm)

24 inches 

(610 mm)

FOOTPRINT

39 inches 

(991 mm)

40 inches 

(1,016 mm)

T-88 THRUST BEARINGS BREAK-IN NOTICE

 (new installation only)

The T-88 Thrust Bearings on the exercise arms of this machine may wear slightly during the first 

3 - 5 weeks of use. Check the exercise arms weekly for proper adjustment during this period. 
Scan the QR code for the “T-88 Thrust Bearings Adjustment” procedure.

NOTE: Bearings may seep a small amount of grease during break-in and is normal during this 
period. If this occurs, wipe off exposed grease daily. After the break-in period, the grease seepage 
will stop.

Содержание 001133BP

























Отзывы: