background image

Benchy 

 Glycol Instruction Manual 

 

Page 

3

 of 

9

 

www.KegLand.com.au 

 

Last Updated 14/12/2020 5:29 PM

 

 

Initial Start-up and Testing 

Important 

 

Let the Benchy sit for at least 24 hours after delivery or after sitting on its side before turning the 

unit on. 

Whenever the Benchy is operating and cooling the reservoir the agitator pump needs to be 

operating to keep the liquid in the reservoir agitated and avoid ice formation. The pump is wired 

into the temperature controller and hence should always be running when the unit is turned on. 

Assemble the sight tube: 

Firmly push 

the two 3/8” duotight tee pieces 

(

KL07023

) onto the push fit tubes on the 

front of the Benchy and push your sight tube into each of the duotight tee pieces as 
shown to the right. Confirm this is held in place securely by pulling on the duotight 
fittings and ensuring they are locked in place. Then, push a 3/8

 plug (

KL06965

into 

each of the duotight tee pieces.  

To remove the plug/tube from the duotight tee piece, push the collar on the tee piece 
in towards the fitting as you pull the plug/tube out of the tee piece.  

Attaching a keg 

On the side of the Benchy 

you will find two 5/8” threaded shanks. Screw 

a duotight 

8mm x 5/8” fitting

 (

KL06903

) onto each of the threaded shanks (ensuring the washer 

is in place internally on the duotight).  

Push 8mm OD EVABarrier hose into the Duotight fitting on the shank on the sight of the Benchy. 

Connect this 8mm OD EVABarrier hose to your coupler or disconnect on your keg.

 

 

 

Содержание Benchy - Glycol










Отзывы:

Похожие инструкции для Benchy - Glycol