KEEWAY 50cc Series Скачать руководство пользователя | Manualshive

Страница: 46 / 64

background image

46

POWERTRAIN COMPONENTS___________________

CARBURETOR REMOVAL/INSTALLATION

Removal

Remove seat/helmet box assembly.

Remove fuel inlet line

Loosen the clamp between carburetor and air box and remove intake duct.

Remove plug from fuel overflow/discharge hose and drain any remaining fuel into a safe
container.

Disconnect enrichment valve pigtail.

Disconnect throttle cable.

Remove carburetor-mounting bolts and carefully remove carburetor.

Installation

Upon ensuring that all wiring and cables are safely tucked away, carefully position
carburetor over engine intake runner and start the mounting bolts. DO NOT TIGHTEN
AT THIS TIME for Flash, hurricane and venus models..

Connect throttle cable and enrichment valve pigtail.

Ensure that fuel overflow/discharge hose plug is in place and secure.

Firmly snug carburetor mounting bolts. DO NOT OVERTORQUE.

Slide intake duct over carburetor throat and tighten clamp.

Connect fuel inlet line.

(before installing seat/helmet box assembly, attempt to start the vehicle. It will take
several seconds, as the fuel bowl must fill. As the vehicle starts, closely inspect all joints
to ensure proper fit and seal.)

Install seat/helmet box assembly.

«
...
44
45
46
47
48
...
»

Содержание 50cc Series

































































Отзывы:

Нет отзывов

Похожие инструкции для 50cc Series

Бренд: Velotric Страницы: 15

Бренд: iWatBoard Страницы: 100

Expedition HURES36

Бренд: HURTLE Страницы: 18

Бренд: Merits Страницы: 30

BEWEGT MIT KOMFORT

Бренд: Stark Products Страницы: 40

Бренд: Dynacraft Страницы: 27

Бренд: WISPEED Страницы: 73

Бренд: Quantum Sphere Страницы: 3

Бренд: CareCo Страницы: 23

Бренд: ICONE Страницы: 42

Бренд: Trikke Страницы: 40

Бренд: Skutis Corporation Страницы: 30

Бренд: FREERIDER Страницы: 36

Бренд: FREERIDER Страницы: 41

Бренд: FREERIDER Страницы: 48

Бренд: Vermeiren Страницы: 204

Бренд: WattWheels Страницы: 22

Бренд: WattWheels Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды