manualshive.com logo in svg

KEB COMBIVERT H6, Инструкция по эксплуатации, Страница: 42 / 62

Поделиться
Скачать
KEB COMBIVERT H6 Скачать руководство пользователя страница 42

4.2  Connection of the power unit

4.2.1  Connection of the DC bus X1D

The copper bars connect the DC bus of the different H6 devices. Precharging, power 

supply and regeneration (if required) is provided by the supply unit. The electrical con-

nection is made with metal bridges, which must be mounted (as illustrated in the photo). 

A plastic cap must be installed at both ends of the H6 system as protection against 

accidental contact.

 DANGER

Caution, dangerous voltage

 

►

The voltage on the DC bus during operation can be up to 840 Vdc!

Bridges for the connection of the 

DC bus between the units

upper rail = DC+

lower rail = DC–

Place plastic cap as protection against 

accidental contact at the end of the 

system

Torx raised-head screw M4 x 10

required tool

Torx screwdriver TX20

Tightening torque 3.0 Nm (bridge)

1.1…1.2 Nm (plastic cap)

Figure 12:  Connection of the DC bus

Attach the cover for the DC bus again after the installation.

4.2.2  Connection of the 24v bus X1C

The 24V bus supplies the control and the driver circuit of the axis module and the power 

supply and regenerative unit with 24V DC voltage. Generally this voltage is provided by 

the COMBIVERT H6 supply unit, but it can also be used by an existing voltage source.

The bridge for the connection of the 24V bus is attached to the units 

and fixed with a screw.

Cross-drive screw M3x10

Tightening torque 0.5 Nm

Figure 13:  Connection of the 24V bus

ATTENTION

The assembly of the jumper must be carried out with special care. Tilting 

or breaking the plug contacts is to be prevented.

42

 CONNECTION OF THE POWER UNIT

All manuals and user guides at all-guides.com

Содержание COMBIVERT H6































































Отзывы:

Нет отзывов