KB Electronics PENTA KB POWER KBRG-225D Скачать руководство пользователя страница 18

Страница: 18 / 18

X – LIMITED WARRANTY

For a period of 18 months from date of original purchase, KB will repair or replace without

charge devices which our examination proves to be defective in material or workmanship.

This warranty is valid if the unit has not been tampered with by unauthorized persons,

misused, abused, or improperly installed and has been used in accordance with the

instructions and/or ratings supplied. The foregoing is in lieu of any other warranty or

guarantee, expressed or implied, and we are not responsible for any expense, including

installation and removal, inconvenience, or consequential damage, including injury to any

person, caused by items of our manufacture or sale. Some states do not allow certain

exclusions or limitations found in this warranty so that they may not apply to you. In any

event, KB's total liability, under all circumstances, shall not exceed the full purchase price

of this unit. (rev 4/88)

KB ELECTRONICS, INC.

12095 NW 39th Street, Coral Springs, FL 33065 • (954) 346-4900 • Fax (954) 346-3377
Outside Florida Call

TOLL FREE

(800) 221-6570 •

E-mail

– [email protected]

www.kbelectronics.com

(A40260) – Rev. C – 1/98

Содержание PENTA KB POWER KBRG-225D


















