Kaysun Prodigy Pro Series, Инструкция по установке и эксплуатации

Страница: 29 / 41

 Page 29 
Outdoor Unit Dimensions (mm) Mounting Dimensions
W x H x D Distance A (mm) Distance B (mm)
681 x 434 x 285 (26.8" x 17.1" x 11.2") 460 (18.1") 292 (11.5")
700 x 550 x 270 (27.5" x 21.6" x 10.6") 450 (17.7") 260 (10.2")
700 x 550 x 275 (27.5" x 21.6" x 10.8") 450 (17.7") 260 (10.2")
720 x 495 x 270 (28.3" x 19.5" x 10.6") 452 (17.8") 255 (10.0")
728 x 555 x 300 (28.7" x 21.8" x 11.8") 452 (17.8") 302 (11.9")
765 x 555 x 303 (30.1" x 21.8" x 11.9") 452 (17.8") 286 (11.3")
770 x 555 x 300 (30.3" x 21.8" x 11.8") 487 (19.2") 298 (11.7")
805 x 554 x 330 (31.7" x 21.8" x 12.9") 511 (20.1") 317 (12.5")
800 x 554 x 333 (31.5" x 21.8" x 13.1") 514 (20.2") 340 (13.4")
845 x 702 x 363 (33.3" x 27.6" x 14.3") 540 (21.3") 350 (13.8")
890 x 673 x 342 (35.0" x 26.5" x 13.5") 663 (26.1") 354 (13.9")
946 x 810 x 420 (37.2" x 31.9" x 16.5") 673 (26.5") 403 (15.9")
946 x 810 x 410 (37.2" x 31.9" x 16.1") 673 (26.5") 403 (15.9")
If you will install the unit on the ground or on a
concrete mounting platform, do the following:
1. Mark the positions for four expansion bolts based
on dimensions chart.
2. Pre-drill holes for expansion bolts.
3. Place a nut on the end of each expansion bolt.
4. Hammer expansion bolts into the pre-drilled holes.
5. Remove the nuts from expansion bolts, and place
outdoor unit on bolts.
6. Put washer on each expansion bolt, then replace
the nuts.
7. Using a wrench, tighten each nut until snug.
WARNING
WHEN DRILLING INTO CONCRETE, EYE
PROTECTION IS RECOMMENDED AT ALL TIMES.
If you will install the unit on a wall-mounted bracket,
do the following:
CAUTION
Make sure that the wall is made of solid brick, concrete,
or of similarly strong material. The wall must be able to
support at least four times the weight of the unit.
1. Mark the position of bracket holes based on
dimensions chart.
2. Pre-drill the holes for the expansion bolts.
3. Place a washer and nut on the end of each expansion
bolt.
4. Thread expansion bolts through holes in mounting
brackets, put mounting brackets in position, and
hammer expansion bolts into the wall.
5. Check that the mounting brackets are level.
6. Carefully lift unit and place its mounting feet on
brackets.
7. Bolt the unit firmly to the brackets.
8. If allowed, install the unit with rubber gaskets to
reduce vibrations and noise.