background image

 

 

15 

            

Operation

 

 

 

 

AUTO-RESTART (on some models) 

If  the  unit  breaks  off  unexpectedly  due  to  the  power cut,  it  will  restart  with  the  previous  function  setting 

automatically when the power resumes. 

WAIT 3 MINUTES BEFORE RESUMING OPERATION 

After the unit has stopped, it can not be restarted operation in the first 3 minutes. This is to protect the unit. 

Operation will automatically start after 3 minutes. 
AIR FLOW DIRECTION ADJUSTMENT 

The louver can be adjusted automatically. Adjust the air flow direction automatically: 

-When the Power is ON, the louver opens fully. 

-Press the SWING button on the panel or remote controller to initiate the Auto swing feature. The louver will 

swing up and down automatically. 

-Please do not adjust the louver manually. 
POWER MANAGEMENT feature(optional) 

When the ambient temperature is lower (Cooling mode) or higher (Heating mode) than the setting 

temperature for a period, the unit will be automatically operating power management feature. The 

compressor and fan motor stop and the power management indicator light 

(  ) illuminates. 
When  the  ambient  temperature  is  higher  (Cooling  mode)  or  lower  (Heating  mode)  than  the  setting 

temperature, the unit will be automatically quit the power management feature. 

The power management indicator light turns dark and the 

compressor and (or) fan motor run.

   

 

Water drainage

 

-During dehumidifying modes, remove the upper drain plug from the back of the unit, install the drain connector (5/8" 

universal female mender) with 3/4" hose (locally purchased). For the models withoutdrain connector, just attach the drain 

hose to the hole. Place the open end of the hose directly over the

 

 

 
 
 

                                                               

Remove the upper drain plug 

 

 

                                                                                 Continuous drain hose 

 

                                                                                                         

 

 

During heating pump mode, remove the lower drain plug from the back of the unit, install the drain connector (5/8" universal female 

mender) with 3/4" hose (locally purchased). For

 

the models without drain connector just attach the drain hose to the 

hole. Place the open end of the Hose adaptor directly over the drain area in your basement floor. NOTE: Make sure the 

hose is secure so there are no leaks.

 

 

                                                                                         

                                                                                           Remove the lower drain plug 

 

                                                                                                           Continuous drain hose                                                       

                                                                             drain hose adaptor                                                                                                                        

                                                                                                                         

Содержание KP-35 HN8

























Отзывы: