Kaysun KMF-200 DN2 Скачать руководство пользователя страница 9

7.2   Troubles and causes of remote controller

 

 

Before  asking  for  serving  or  repairing  ,  check  the  following 
points.

 

(see in Table 7-2)

 

 

 

Table 7-2 

 

 

Symptoms  

Causes

 

Solution

 

 

 

 

 

The fan  speed  can  not  be 
changed.

 

 

Check whether the MODE 
indicated on  the display is 
"AUTO"

 

 

 

Check whether the  MODE 
indicated on  the display is 
"DRY"

 

 

When the automatic mode is 
selected, the air conditioner will 
automatically change the fan 
speed.

 

When dry operation is selected, 
the air conditioner automatically 
change the fan speed. The fan 
speed can be selected during

 

"COOL" , "FAN ONLY", 

and "HEAT"

 

 

The remote  controller  signal  is 
not transmitted  even  when

 

the  ON/OFF  button  is pushed.

 

Check whether the batteries 
in the remote controller are 
exhausted.

 

 

The power supply is off.

 

 

 

The  TEMP.  indicator  does 
not come  on.

 

Check whether the MODE

 

indicated on the display is

 

FAN ONLY

 

The temperature cannot be set during

 

FAN mode.

 

 

The indication  on the  display 
disappears  after  a lapse  of 
time.

 

Check whether the timer 
operation has come to an 
end when the TIMER OFF

 

is indicated on the display.

 

The air conditioner operation will 
stop up to the set time

 

 

 

The  TIMER  ON  indicator 
goes  off  after  a  lapse  of 
certain  time.

 

Check whether the timer 
operation is started when 
the 

TIMER ON 

is indicated 

on the display.

 

Up to the set time, the

 

air conditioner will automatically 
start and the appropriate

 

indicator will go off.

 

 

 

 

No receiving  tone  sounds 
from  the indoor  unit even 
when  the ON/OFF  button  is 
pressed.

 

Check whether the signal 
transmitter of the remote 
controller is properly directed 
to the infrared signal receiver 
of the indoor unit when the 
ON/OFF button is pressed.

 

Directly transmit the signal transmitter of 
the remote controller to the

 

infrared signal receiver of the

 

indoor unit, and then repeatedly 
push the ON/OFF button twice.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

owner's manual 

 

Содержание KMF-200 DN2













Отзывы: