background image

3 BEFORE INSTALLATION

3.1 Handling of the unit

The angle of inclination should not be more than 15º when carrying the unit in case of overturn of the unit.
1) Rolling handling: several rolling rods of the same size are placed under the base of the unit, and the length of each rod must

be more than the outer frame of the base and suitable for balancing of the unit.

NOTE

About Fluorinated Gasses
- This air-conditioning unit contains fluorinated gasses. For specific information on the type of gas and the amount,

please refer to the relevant label on the unit itself. Compliance with national gas regulations shall be observed.
- Installation, service, maintenance and repair of this unit must be performed by a certified technician.
- Product uninstallation and recycling must be performed by a certified technician.
- If the system has a leak-detection system installed, it must be checked for leaks at least every 12 months. When

the unit is checked for leaks, proper record-keeping of all checks is strongly recommended.

Do not install the unit in the following places:
- Where there is mist of mineral oil, oil spray or vapors. Plastic parts may deteriorate, and cause possible loose or

water to leak.
- Where corrosive gases (such as sulphurous acid gas) are produced. Where corrosion of copper pipes or soldered

parts may cause refrigerant leakage.
- Where there is machinery which emits electromagnetic waves. Electromagnetic waves can disturb the control

system and cause equipment malfunction.
- Where flammable gases may leak, where carbon fiber or ignitable dust is suspended in the air or where volatile

flammables such as paint thinner or gasoline are handled. These types of gases might cause a fire.
- Where the air contains high levels of salt such as near the seaside.
- Where voltage fluctuates a lot, such as in factories.
- In vehicles or vessels.
- Where acidic or alkaline vapors are present.
Children should not play with the unit. Cleaning and user maintenance should not be done by children without 

supervision.
This appliance is intended to be operated by expert or trained users in shops, in light industry and on farms, or for 

commercial use by lay persons
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified 

person in order to avoid a hazard.
DISPOSAL: Do not dispose this product as unsorted municipal waste. Collection of such waste seperatelly for 

special treatment is necessary. Do not dispose of electrical appliances as municipal waste, use seperate collection 

facilities. Contact your local goverment for information regarding the collection systems available. If electrical 

appliances are disposed of in landfills or dumps, hazardous substance can leak into the groudwater and get into the 

food chain, damaging your health and well-being.
The  wiring must be performed by professional technicians in accordance with national wiring regulation and this 

circuit diagram. An all-pole disconnection device which has at least 3mm seperation distance in all pole and a 

residualcurrent device(RCD) with the rating not exceeding 30mA shall be incorporated in the fixed wiring according 

to the national rule.
Confirm the safety of the installation area ( walls, floors, etc. ) without hidden dangers such as water, electricity, and 

gas before the wiring and piping works.
Before installation , check whether the user's power supply meets the electrical installation requirements of unit ( 

including reliable grounding , leakage , and wire diameter electrical load, etc. ). If the electrical installation 

requirements of the product are not met, the installation of the product is prohibited until rectified.
When installing multiple units in a centralized manner, please confirm the load balance of the three-phase power 

supply, and multiple units are prevented from being assembled into the same phase of the three-phase power 

supply.
Product installation should be fixed firmly, Take reinforcement measures, if necessary.

04

Содержание KEM-140 DRS5 KH





























































Отзывы: