background image

8.3 Outdoor unit PCBs

8.3.1 MAIN PCB

NO.

1
2
3

4
5
6
7
8
9

10
11

Detail information

CN32

Main board power supply.

Table 8-2

CN99:slave board power supply

.

CN75/CN66:EVA-HEAT,Electric of water side heat exchanger heaters connection

CN74/CN67:CCH,Crankcase heater

CN48:ST1,Four-way valve
CN47:SV6,Liquid bypass solenoid valve
CN49:SV5,Multi-function solenoid valve
CN84:SV8A,Injection solenoid valve of compressor system A
CN83:SV8B,Injection solenoid valve of compressor system B
CN93

The alarm signal output of the unit(ON/OFF signal)

Attention: the control port value of the alarm actually detected is ON/OFF but not 220-240V control power supply

so 

special attention should be paid when installing the alarm signal output.

CN68:Pump(220-240V control power supply )

1

After receiving start-up instruction, the pump will be started up instantly, and will maintain start-up state always

in the  process of operation.

2

In case of refrigerating or heating shutdown, the pump will be shut down 2 minutes after all modules stop

operating.

3

In case of shutdown under the pump mode, the pump can be directly shut down.

1) Label descriptions are given in Table 8-2

16

1

2

3

4

5

6

8

7

9

10

11

13 12

Fig. 8-9   Main board of  

KEM-75 DRS5 KH

 and 

KEM-140 DRS5 KH

14

15

19

22

24

26

28

29

31

33 34

38 39

36

35

25

27

30

32

18

20

21

23

17

37

15

Содержание KEM-140 DRS5 KH





























































Отзывы: