background image

Safety 

Precautions

Page 6

 WARNINGS FOR PRODUCT INSTALLATION

1.

Installation must be performed by an authorized dealer or specialist. Defective installation can

cause water leakage, electrical shock, or fire.

2.

Installation must be performed according to the installation instructions. Improper installation

can cause water leakage, electrical shock, or fire.

3.

Contact an authorized service technician for repair or maintenance of this unit. This appliance

shall be installed in accordance with national wiring regulations.

4.

5.

6.

 

7.

8.

9.

10.

11.

  

  

Only use the included accessories, parts, and specified parts for installation. Using non-standard

 

parts can cause water leakage, electrical shock, fire, and can cause the unit to fail.

Install the unit in a firm location that can support the unit’s weight. If the chosen location cannot

 

support the unit’s weight, or the installation is not done properly, the unit may drop and cause

 

serious injury and damage.

Install drainage piping according to the instructions in this manual. Improper drainage may

 

cause water damage to your home and property.

For units that have an auxiliary electric heater, 

do not 

install the unit within 1 meter of

 

any 

combustible materials.

Do not

 install the unit in a location that may be exposed to combustible gas leaks. If

 

combustible gas accumulates around the unit, it may cause fire.

Do not turn on the power until all work has been completed.

When moving or relocating the air conditioner, consult experienced service technicians for

 

disconnection and reinstallation of the unit.

How to install the appliance to its support, please read the information for details in "indoor unit

 

installation" and "outdoor unit installation" sections .

Note about Fluorinated Gasses

1.  

This air-conditioning unit contains fluorinated greenhouse gasses. For specific information on the

type of gas and the amount, please refer to the relevant label on the unit itself or 

the

 “Owner's Manual - Product Fiche ” in the packaging of the outdoor unit. 

(European

Union products only)

.

2.

 

Installation, service, maintenance and repair of this unit must be performed by a certified

technician.

3.

Product uninstallation and recycling must be performed by a certified technician.

4.  

For equipment that contains fluorinated greenhouse gases in quantities of 5 tonnes of CO

2

equivalent or more, but of less than 50 tonnes of CO

2

 equivalent, If the system has a leak-

detection system installed, it must be checked for leaks at least every 24 months.

5.

 

When the unit is checked for leaks, proper record-keeping of all checks is strongly recommended.

Содержание KCI-26 DMR14

















































Отзывы: