KAYO MOTOR TT 125 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 74

background image

Front brake sheet

Check the caliper brake sheet thickness, if the thickness of the
brake sheet is less than the minimum thickness, the brake sheet
must be replaced.
The minimum thickness of a brake sheet is1mm

。

Note:

the brake sheets should be replaced as a whole. If you

are not sure to complete the replacement work, please go to the
KAYO dealer,let the professional personnel to complete the
replacement.

Check the free movement of the foot brake

Rear brake pedal:
Under normal circumstances, the free movement of the brake
pedal should be shown in the table below. Check the brake
lever and make sure the movement is correct.

Model

Brake pedal free movement

TT125

20

～

55mm

Check the rear disc brake fluid level

Observe the fluid level hole and check the level of the brake
fluid.  The fluid level should be more than half of the
observation hole, that is, the fluid level should be higher than
the "LOWER".  If brake fluid is insufficient, add it
immediately.

Note:

do not let the brake fluid splash on the paint surface, easy

to cause corrosion.

Danger:

please pay attention to check whether the brake fluid

leakage, brake fluid tube is damaged. If there is leakage
problem, please contact KAYO dealer.

Refill rear disc brake fluid

«
...
28
29
30
31
32
...
»

Содержание TT 125











































































Отзывы:

Нет отзывов

Похожие инструкции для TT 125

Turismo Veloce 800 LUSSO

Бренд: AGUSTA Страницы: 616

Бренд: LAZER Страницы: 2

Бренд: Jialing Honda Страницы: 10

Бренд: Spartus Страницы: 24

Easyrack 6612533 01 01

Бренд: hepco & becker Страницы: 5

Бренд: Megelli Страницы: 83

Super Tenere XTZ1200Z

Бренд: Yamaha Страницы: 108

Бренд: Yamaha Страницы: 100

Бренд: Yamaha Страницы: 351

Бренд: Yamaha Страницы: 96

Бренд: Husqvarna Страницы: 12

Бренд: Husqvarna Страницы: 12

Бренд: Husqvarna Страницы: 7

Бренд: Husqvarna Страницы: 32

Бренд: Husqvarna Страницы: 7

Бренд: Husqvarna Страницы: 128

Бренд: Malaguti Страницы: 272

Бренд: Yamaha Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды