manualshive.com logo in svg

KAYO MOTOR STORM 150, Руководство по обслуживанию

Поделиться
Скачать
KAYO MOTOR STORM 150 Скачать руководство пользователя страница 36

ZHEJIANG KAYO MOTOR CO., LTD.

 

WWW.RIDEKAYO.COM

 

The brake pads, caliper and disc are normal wear and tear items 

 

Check or replace the brake disc

 

● 

Check the surface of brake disc, if it is worn, damaged, bent, or grooved 

replace. 

● 

If the disc thickness is less than 3.0mm, replace. 

Check or replace brake pads

 

● 

Check thickness of pads, If it’s less than 1.5mm, replace.

 

● 

Check for damage, cracks, and uneven wear. Replace pad set if out of 

specification 

 

Note: Replace pads in sets.

 

 

 

 

3.5 

Wheel

 

With the atv on a jack of atv lift. Lift the 

front  wheels  off  the  ground.  Push  and 

pull the wheel in and out as shown in the 

diagram. 

If  there  is  movement,  check  torques  on 

hub, steering shafts, spindles.

 

If there is still movement, check the 

bearings, ball joints, a-arm bushings. 

Replace if worn or damaged. 

 

 

 

。 

Front wheel size

 

Содержание STORM 150

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды