KAYO MOTOR AT125-B Скачать руководство пользователя страница 39

Страница: 39 / 96

ZHE JIANG KAYO MOTOR CO., LTD

www.RideKayo.com

－

oil pump

－

carburetor, air filter

－

cylinder head cover, start motor, cylinder head, cylinder block, camshaft

－

left cover, AC magneto

－

piston, piston ring, piston pin

●

Remove the engine in following operations.

－

Crankshaft, main and counter shaft

Tightening torque

See 1.5

4.2 Fuel system

asoline is flammable and explosive. Pay attention to sparks and open flame.

Vaporized gasoline may explode if exposed to open flame or sparks, please choose

well-ventilated areas away from these hazards when refueling or working on the fuel

system and its related components.

Fuel tank removal

Remove the plastic body parts, remove fuel lines from tank and fuel valve, then

remove tank mounting bolts and tank.

*Fuel tank pictures may differ from tanks on U.S. models

oil

pipe1

oil

switch

bolt2

Содержание AT125-B

































































































Результаты поиска

Содержание AT125-B

Отзывы:

Бренды по названию

Популярные бренды

KAYO MOTOR AT125-B, Руководство по обслуживанию

Результаты поиска

Содержание AT125-B

Отзывы:

Бренды по названию

Популярные бренды