KAYO MOTOR AT125-B Скачать руководство пользователя страница 33

Страница: 33 / 96

ZHE JIANG KAYO MOTOR CO., LTD

www.RideKayo.com

Note:

●

When adding brake fluid, do not mix with dust or water, always add fluid from a

new sealed container.

●

Brake fluid can damage plastic, painted, and rubber surfaces. Wipe clean

immediately if any is spilled

Front brake disc and brake pads

The brake pads, caliper and disc are normal wear and tear items

Check or replace the brake disc

● Check the surface of brake disc, if it is worn, damaged, bent, or grooved replace.

● If the disc thickness is less than 3.0mm, replace.

Check or replace brake pads

● Check thickness of pads, If it’s less than 1.5mm, replace.

● Check for damage, cracks, and uneven wear. Replace pad set if out of specification

Note: Replace pads in sets.

3.4

Wheel

With the atv on a jack of atv lift. Lift the

front wheels off the ground. Push and

pull the wheel in and out as shown in the

diagram.

If there is movement, check torques on

hub, steering shafts, spindles.

If there is still movement, check the

Brake fluid lower
limit

Содержание AT125-B

































































































Результаты поиска

Содержание AT125-B

Отзывы:

Бренды по названию

Популярные бренды

KAYO MOTOR AT125-B, Руководство по обслуживанию

Результаты поиска

Содержание AT125-B

Отзывы:

Бренды по названию

Популярные бренды