Kaval BDA-1000 Скачать руководство пользователя страница 5

Страница: 5 / 16

Page 5

Kaval Telecom Inc.

DCM000000001

•

BLOCK DIAGRAM

REJECT FILTER #2

UPLINK DIRECTION

IN BUILDING

ANTENNA

COOLING FANS

VENTILATION

INPUT

AC POWER

TERMINAL BLOCK

VENTILATION

BDA

SUPPLY

28V POWER

CONTROLLER

ROOF TOP

DOWNLINK DIRECTION

PA #1

REJECT FILTER #1

PA #2

BOOSTER #1

BOOSTER #2

Power and Control Connections

-------

RF Connections

____

BDA Controller :

An enclosed unit with microcontroller, LED indicators, buttons, and two-line display.

Temp Sense & Cooling Fans :

Controlled by the BDA Controller to ensure safe and reliable operation.

28V Power Supply :

Providing all DC Power, with optional Gell-Cell Battery Backup.

Duplexers :

Isolating Downlink and Uplink Frequencies, and coupling to antennas.

Reject Filters :

Installed if required to eliminate feedback.

Boosters :

High Gain (11 to 65 dB) Linear Amplifiers supplying up to 1 Watt of RF Power. The
basic gain is adjustable via the BDA Controller over a 33 to 65 dB range, and an
Automatic Gain Control (AGC) provides an additional 23 dB range.

PA Power Amplifiers :

Optional Linear Power Amplifiers providing 15 dB of additional gain, and up to 20 Watts
of RF Power.

Содержание BDA-1000

















Результаты поиска

Содержание BDA-1000

Отзывы:

Бренды по названию

Популярные бренды

Kaval BDA-1000, Руководство пользователя

Результаты поиска

Содержание BDA-1000

Отзывы:

Бренды по названию

Популярные бренды