background image

 

Operating Manual 

 

10 

Original Operating Manual

 

 

4.1.2  Fork carriage 

 

 

 

   

Using appropriate lifting means, lift the attachment at the positions indicated (1). 

   

Demount the lower hooks (2). 

   

Mount the attachment on the fork carriage of the lift truck (3). 

   

Check that the attachment is correctly seated in the centre lock (4).

 

   

Mount the lower hooks (2), tightening the screws (5) with a torque of 190 Nm. 

   

Use pipes or hoses to connect the hydraulic ports (6) to the hydraulic ports of the lift truck.

 

 

 

Demount the safety retaining stops (7) and limit stops (8) and slide the fork arms from the 
side onto the fork carriage. 

 

  Ensure that all safety retaining stops (7) and limit stops (8) are remounted. 

 

 

Before initial operation, check the functions and the identification of the attachment with the 
movement directions of the operating elements (operating lever, joystick, etc.). 

 

 

Mount the residual carrying capacity notice and identification of the operating elements (if 
not already present) of the combination of lift truck/attached equipment on the lift truck. 

 

Содержание 0,8 T351.2
























Отзывы: